The Original CZ Forum
CZ LONG ARMS => CZ Scorpion EVO => Topic started by: Vincent_Diesel on November 16, 2019, 09:26:21 PM
-
Hi, first post here.
Bought a used EVO Scorpion, low rounds, priced well and seems to be mechanically solid. Indoor range I belong to only carries Federal 115 grain ammo, and have been experiencing FTFs and jams the first time out. Been reading that 115 grain just doesn’t have enough energy to fully cycle the bolt. Planning on ordering some 124 grain to test, but I was under the impression the EVO isn’t fussy.
Anybody else experiencing this issue? Any suggestions? TY.
-
Hi, first post here.
Bought a used EVO Scorpion, low rounds, priced well and seems to be mechanically solid. Indoor range I belong to only carries Federal 115 grain ammo, and have been experiencing FTFs and jams the first time out. Been reading that 115 grain just doesn’t have enough energy to fully cycle the bolt. Planning on ordering some 124 grain to test, but I was under the impression the EVO isn’t fussy.
Anybody else experiencing this issue? Any suggestions? TY.
What mags are you using? Have you tried switching to a different or new mag? My Scorpion micro has eaten everything I've thrown at it.
Sent from my Pixel 2 XL using Tapatalk
-
I fired 115, 124, 147, and 165 grain stuff today with no issues or problems with any of them in mine.
-
Shot couple hundred rounds of Czech Sellier Bellot 115 grain today, zero issues. Few thousand 115 grains in the past, again zero issues.
-
Using the factory 10 round mags. Sigh.
I do have some new mags on order hopefully ruling out a mag feed problem. Really bummed about this, I really like the carbine.
-
Using the factory 10 round mags. Sigh.
I do have some new mags on order hopefully ruling out a mag feed problem. Really bummed about this, I really like the carbine.
Take a look at the feed lips and pick up some different ammo somewhere else and try that.
Sent from my Pixel 2 XL using Tapatalk
-
I have never had any issues related to ammo.
However, I have recently had all kinds of issues with other 9mm guns. It turns out that the entire 1,000 round batch of 9mm I bought had a goofy shape to the case and gave the ejector trouble in basically all of my guns.
Your issue may be different, but I would clean and lube the gun, then try some different ammo. See if that works.
-
Using the factory 10 round mags. Sigh.
I do have some new mags on order hopefully ruling out a mag feed problem. Really bummed about this, I really like the carbine.
Also what type of failure are you having?
-
Yes. Thanks for the help.
At the range been using the same Federal 115 grain ammo in a Beretta Storm and Sig P320. Not a single issue. The bolt on the scorpion has more weight, very robust so I figured it that may be related to the load. Spent the entire day cleaning the bolt, did see some heavy powder residue on certain parts. Hopefully that will resolve the issue.
-
Yes. Thanks for the help.
At the range been using the same Federal 115 grain ammo in a Beretta Storm and Sig P320. Not a single issue. The bolt on the scorpion has more weight, very robust so I figured it that may be related to the load. Spent the entire day cleaning the bolt, did see some heavy powder residue on certain parts. Hopefully that will resolve the issue.
Describe the failure
Sent from my Pixel 2 XL using Tapatalk
-
Bullet stuck, slightly lower and behind spent cartridge. Upon clearing and inspection no sign of light primer strike.
-
Bullet stuck behind spent cartridge, upon clearing and inspection no light primer strike.
So a failure to extract? Have you looked at your extractor?
Sent from my Pixel 2 XL using Tapatalk
-
I have never run the bolt on my Scorpion “dry”. But I can’t help but wonder what kind of failures it would produce if I did.
-
Bullet stuck behind spent cartridge, upon clearing and inspection no light primer strike.
So a failure to extract? Have you looked at your extractor?
Sent from my Pixel 2 XL using Tapatalk
Yes, thanks for clearing that up, failure to extract would be more accurate.
Last night based on suggestions I thoroughly cleaned and lubed gun. Tried new ammo, American Eagle 9mm and same 115 grain. Out of 200 rounds I managed a lower fail rate of 3 jams. Better, but I am trying for zero fails.
Here is a picture of the jammed bullet stuck behind the fired un-extracted cartridge. All jams seem to have a strange chamfer around the bottom edge. Any thoughts to this? I am feeling like I should be returning this Scorpion in exchange for a new one.
(https://i1336.photobucket.com/albums/o649/VincentDiesel/Bullet%20Jam/bullet_zpsphlf5ix8.jpg)
-
So a failure to extract? Have you looked at your extractor?
Also attached a photo of the extractor after a quick cleaning. Correct me if I'm wrong but seems to be okay correct?
(https://i1336.photobucket.com/albums/o649/VincentDiesel/Bullet%20Jam/extractor_zpshhfffwuj.jpg)
-
first glance says that extractor looks fine, how well does it pivot, is there any binding?
I know my 20rd mags had 30rd springs in them, resulting in too much spring force when the mag was loaded, had to cut them to get equivalent force to the 30rd mags, it could be possible the 10rd mags are iffy, how many rounds are in the mag when it jams?
As for 115gr not having enough energy, that is crap, this is a blowback gun and even weak sauce 115gr like magtech seems to work fine (at least in mine). 115gr does NOT work in my "duty pistols" which are sprung for 115+p or NATO rounds, they will fire but stovepipe or not fully extract, as a browning action is much more sensitive to energy, too little and you have extraction problems, too much and the slide slams back with too much recoil and poor reliability.
-
Have you done a bolt tear down and thorough cleaning of the extractor and recess. Pay particular attention to reassembly, spring condition and parts orientation. Here is a link to a decent video showing disassembly/reassembly:
https://www.youtube.com/watch?v=zmokE2mmwOA
The rub/scuff mark on the rim of the loaded round appears normal for the extractor attempting to snap over the rim.
Take a good look at the ejector to make sure the tip hasn't been damaged or broken off.
I agree with what others have said, in that the Scorpion's blowback action should function with ANY factory in spec ammo. Mine thrive on Wolf steel cased ammo, which tends to feel a little on the weak side.
-
Thanks all for the help.
Bit of an update. After a very thorough cleaning and a complete bolt disassembly, I went back to the range. I also used a different magazine (newer CZ black window magazines). Good news is that out of 100 rounds I managed to get down to 2 failures, same 115 grain range ammo. Much improved, but still looking for zero malfunctions which I know this PCC is capable of. This time it wasn’t a failure to extract (it seems to be extracting fine now after cleaning) but looked more like failure to fire. Bullet looked to be seated in the barrel when I peeked inside chamber.
When I got home I did another complete bolt disassembly and I had noticed something unusual, like an extra part. The manual didn’t call for, or even listed this as a part. It looks like a washer that slides in before the main recoil spring. A washer that in my guess, looks like it is intended to create more spring tension. Anybody know what this is? My brain is telling me, this is what may be causing 115 grain loads to possibly not have enough energy to fully blow back the bolt causing my jams. Was it a post add on part either from CZ or from the original owner?
(https://i1336.photobucket.com/albums/o649/VincentDiesel/Bullet%20Jam/EV__recoil_zpsvoejbk82.jpg)
-
Have you done a bolt tear down and thorough cleaning of the extractor and recess. Pay particular attention to reassembly, spring condition and parts orientation. Here is a link to a decent video showing disassembly/reassembly:
https://www.youtube.com/watch?v=zmokE2mmwOA
The rub/scuff mark on the rim of the loaded round appears normal for the extractor attempting to snap over the rim.
Take a good look at the ejector to make sure the tip hasn't been damaged or broken off.
I agree with what others have said, in that the Scorpion's blowback action should function with ANY factory in spec ammo. Mine thrive on Wolf steel cased ammo, which tends to feel a little on the weak side.
By the way this video is amazing!
-
I'll be honest with you, I have never had a need to disassemble my recoil spring /guide rod assembly, but you are correct, that part does not appear on the parts diagram. I believe your hunch that it was added to provide additional tension to the recoil spring may be the source of your failure to extract the lighter bullet ammo problem. Was the "spacer" on the guide rod, inside the bolt, in front of the recoil spring? This video animation of the complete disassembly and reassembly of the Scorpion and sub-assemblies doesn't show that spacer either. https://www.youtube.com/watch?v=u_bsC3ppfwo
-
Yes. Precisely, on the guide rod, inside the bolt in front of the recoil spring. Have removed the anomaly and will hit the range this week.
-
Just want to say thank you to those who helped me figure this out. Glad to say that after my last range visit, I report Zero malfunctions, after 100 rounds. It was the darn spacer that somebody decided to modify.
What I've learned:
• Don't mess with internals unless you really know what you are doing
• When buying used, buy as close to stock form, know what you are getting in to
• So important to properly maintain your gun, includes knowing how to tear it down and properly put it back together again
Thanks again all!
-
I would assume that is an intentional modification from a prior owner who liked to shoot +p or +p+ ammo or suppressed and needed some extra spring pressure to mitigate the slam-back of the extra recoil, I shoot mostly NATO spec ammo, but have a very effective muzzle brake so it feels like a .22
-
I’ll agree with everyone saying that spacer is not a normal, factory part. FWIW, on these blowback pcc’s, dirty extractors will cause failures to extract. I recently tore my own EVO bolt apart after about 2,500 rounds and scraped out a bunch of greasy gunk from on and around the claw. I had been having FTE every 2 or three rounds. After cleaning, just dumped 200 flawless rounds through it. Seemed to remedy the problem.