The Original CZ Forum
GENERAL => Cajun Gun Works => Topic started by: Kuggoz on January 21, 2022, 06:41:06 AM
-
Hello,
I recently purchased 10x barrel bushing for my shadow 2 and managed to install it without problems. However when I now try to assemble the gun, I no longer can fit the barrel in the slide. As shown in some tutorial videos, I gave it a few very light taps due to it being so tight and it drops in but refuses to move forward at all inside the slide and past the bushing. The barrel can still be removed with relative ease from the slide.
I will attach a couple pictures I took to try and show the situation a bit better.
-
Did you use loctite during installation?
Sent from my iPhone using Tapatalk
-
Did you use loctite during installation?
Sent from my iPhone using Tapatalk
No I did not and don’t remember reading about this either or it being mentioned in the videos.
And something I forgot to mention earlier; I tested the bushing before installing and it fit around the barrel just fine, though tightly.
-
I had CG install mine while they were milling the slide for an optic. It's tight getting the barre in and out of the slide, but otherwise no issue.
-
The bushing is held in place by the front sight pin. No locktite needed.
Please don't think that this is a flippant answer...you really need to hold your mouth open just the right way and it will suddenly slide into the bushing. Same with removing it.
I have to gently fiddle with it and before I can pay attention to what I exactly did it will suddenly fit in.
There have been plenty of threads asking this same question.
-
Hello,
I recently purchased 10x barrel bushing for my shadow 2 and managed to install it without problems. However when I now try to assemble the gun, I no longer can fit the barrel in the slide. As shown in some tutorial videos, I gave it a few very light taps due to it being so tight and it drops in but refuses to move forward at all inside the slide and past the bushing. The barrel can still be removed with relative ease from the slide.
I will attach a couple pictures I took to try and show the situation a bit better.
Your quickest solution would be to call CGW directly.
-
Hello,
I recently purchased 10x barrel bushing for my shadow 2 and managed to install it without problems. However when I now try to assemble the gun, I no longer can fit the barrel in the slide. As shown in some tutorial videos, I gave it a few very light taps due to it being so tight and it drops in but refuses to move forward at all inside the slide and past the bushing. The barrel can still be removed with relative ease from the slide.
I will attach a couple pictures I took to try and show the situation a bit better.
Your quickest solution would be to call CGW directly.
I’m 10 timezones from them in another country, so thought I’d try asking here in case people have had similar experiences.
-
The bushing is held in place by the front sight pin. No locktite needed.
Please don't think that this is a flippant answer...you really need to hold your mouth open just the right way and it will suddenly slide into the bushing. Same with removing it.
I have to gently fiddle with it and before I can pay attention to what I exactly did it will suddenly fit in.
There have been plenty of threads asking this same question.
Ive spent hours trying to fiddle it and giving light taps to it like shown in the few videos about the installation. Will keep trying.
-
Will the barrel move into the bushing if you stick the muzzle end into the bushing from the front of the slide? I'm wondering if you caused any distortion upon installing the bushing? Also did you line up the notch in the bushing so the sight pin slides in as it should?
-
Will the barrel move into the bushing if you stick the muzzle end into the bushing from the front of the slide? I'm wondering if you caused any distortion upon installing the bushing? Also did you line up the notch in the bushing so the sight pin slides in as it should?
It does not fit from the front. I was thinking about the dostortion as well, but how would this happen? I lined up the notch and it went perfectly on the first try, tested it with punch before instaling the pin. It went in quite easily as well. What you imagine could have caused the distortion?
-
Here are the pictures showing how far the barrel is able to go
(https://i.gyazo.com/e9b9726b283b61d62509d725a19f4fc5.png)
(https://i.gyazo.com/daf57cc05f42c87d722d559c27f3fe94.png)
-
Can you reassemble the gun?
Sent from my iPhone using Tapatalk
-
The bushing is held in place by the front sight pin. No locktite needed.
Please don't think that this is a flippant answer...you really need to hold your mouth open just the right way and it will suddenly slide into the bushing. Same with removing it.
I have to gently fiddle with it and before I can pay attention to what I exactly did it will suddenly fit in.
There have been plenty of threads asking this same question.
CZ’s can still spit the bushing out even with the pin installed. Using a retaining compound will combat this.
Sent from my iPhone using Tapatalk
-
I would measure barrel O.D and bushing I.D.
Contact CGW with the measurements. Guessing the bushing is out of spec.
-
I would measure barrel O.D and bushing I.D.
Contact CGW with the measurements. Guessing the bushing is out of spec.
I agree and CGW does also show different size bushings for the regular guns vs the Shadow so I wonder if he either ordered the wrong one or was mistakenly sent the wrong one.
-
There is zero chance he has the wrong bushing if the barrel is able to be installed. The Shadow barrel is 0.550 inch, the standard barrel is 0.500 inch.
It's tough to tell by the pictures but is the bushing fully installed? It looks like it may not be flush with the muzzle end of the slide? If that bushing is not colinear with the barrel it may not allow it to move. It needs to be flush with the end of the slide to ensure it is colinear with the barrel
I'd second measuring the bushing diameter and the barrel diameter. If you can't insert the barrel backwards into the bushing, then something is out of spec.
Cheers,
Toby
-
I had them put a 10x bushing in one of mine, and while I was able to move the barrel back and forth and it shot just fine, I could not pull the barrel out of the gun. It was that tight. I ended up putting the old bushing back in the gun.
-
I had them put a 10x bushing in one of mine, and while I was able to move the barrel back and forth and it shot just fine, I could not pull the barrel out of the gun. It was that tight. I ended up putting the old bushing back in the gun.
Help me out with this one if you would. You couldn't get the barrel out, yet put the old bushing back in? How did you do that?
-
I sent the slide back to CGW and they took care of it.