The Original CZ Forum
GENERAL => CZ Custom => Topic started by: Arndog762 on May 28, 2022, 12:35:50 PM
-
Any plans for a frame mounted red dot mount? :)
-
I asked the same question via email. On 4 April I received this answer: “We are making a new mount to be compatible. Would estimate about 8 weeks till ready.” Based on this, should be available the 2nd week of June (I hope)!!
-
Thank you!👍
-
Got the mount installed yesterday. Had to get longer hardware to be able to use the stock thumbrest/gas pedal.
(https://i.ibb.co/0KYB1WK/6-DE95-BD8-C409-4-FBC-8-AA4-942-FBE10159-E.jpg) (https://ibb.co/gdtvQXd)
-
Did you have any issue removing the rear sight?
-
No the sight slid right off with a quick tap with a brass punch and small hammer.
-
CZC mount compatible with TS2 Green
https://czcustom.com/multi-optic-side-scope-mount.html
longer screws to use factory thumb rest.
https://czcustom.com/tso-thumb-rest-screw-set.html
-
I received the optic mount that fits the Race Green, and frankly I’m a bit disappointed in CZC. Installing the Thumb Rest over the optic mount looks, well, like a Rube Goldberg installation. Mounting a countersink device over a countersink device… Mounting a thumb rest that has a frame cut out flange over the red dot mount that doesn’t have a flange cut out… Really disappointed in CZC’s design and engineering in this application. For now I think I will use the optic mount without the thumb rest until I can find a throttle that blends with the optic mount or CZC decides to “blend” the thumb mount into the optic mount.
-
I received the optic mount that fits the Race Green, and frankly I’m a bit disappointed in CZC. Installing the Thumb Rest over the optic mount looks, well, like a Rube Goldberg installation. Mounting a countersink device over a countersink device… Mounting a thumb rest that has a frame cut out flange over the red dot mount that doesn’t have a flange cut out… Really disappointed in CZC’s design and engineering in this application. For now I think I will use the optic mount without the thumb rest until I can find a throttle that blends with the optic mount or CZC decides to “blend” the thumb mount into the optic mount.
The thumbrest mount for the TS2 is coming as we run out of inventory of the TSO variant. just need patience.
-
Installed the side mount without the thumbrest. Used M4X8 screws which provide sufficient grip length without penetrating the grip wall. The Slide really requires a Slide Charge Handle to safely handle the weapon, Have one on order. Arndog762, thanks for the tips.
(https://i.imgur.com/uk3hkjb.jpg?1)
-
A slide charging handle is definitely a must have. Really happy with the ArmoryCraft one on my TSO so got one for the TS2 too.
(https://i.ibb.co/SJzb0tt/DFFEB4-D7-429-C-4-C91-92-F8-93-BAEB720661.jpg) (https://ibb.co/jHSmGyy)
-
Have the same one on order! Out of curiosity, how was the fit in the sight cut??
-
Slides right in with no effort. Used blue Loc-tite on the setscrew on my TSO and have never had it come loose. Did the same on the TS2.
-
Dialed in at the range today, 10, 15 and 25 yards. Really looking forward to the “Charging Handle” arriving Thursday!!
(https://i.imgur.com/hp9cTLb.jpg)
-
Nice! 8)
-
Hi - thanks for the pictures with the side mount. What competition holster do you use?
-
It’s pretty much a range toy so I’ve never looked at getting a holster for it.
-
Is there a rear mounting plate for red dot for racing green?
-
If you’re referring to a “Sight Cut” mount plate for a red dot, CZ has them available for all of their sight cuts. Having said that I would avoid them like the plague!! On the Race Green the Red Dot Side Mount is the way to go using the tapped holes on the grip dust cover. IF you want the red dot mounted on the slide then have it milled for your red dot. Wicked Arms in Baton Rouge Louisiana does an outstanding job for a reasonable price and with a very quick turn! Your listening to the voice of experience!!
-
I guess I’ll have to pick one of these mounts up. Looks good on there
-
Good Grief, this thing SHOOTS!! (It has become my favorite!!)
(https://i.imgur.com/TWTSsto.jpg?1)
(https://i.imgur.com/uYYtfGP.jpg?1)
-
Very Nice! 8) Suppresses really well too. ;D
(https://i.ibb.co/sVhMqtg/9761-AFA2-CBC0-479-F-8647-C9-C3-BEE9-B661.jpg) (https://ibb.co/vjbKkDc)
-
Hey guys - new member here. just following this as I just got a racing green ts2 and very interested in the red dot mount with the gas pedal. it looks like you have a spacer plate between the gas pedal and the mount? can you elaborate on that a little, I am hoping to set mine up like yours. all help appreciated. Thanks from South Alabama.
-
No spacer. Just mount the stock gas pedal to the optic mount. I believe CZ Customs sells longer hardware that you’ll need.
-
You can also buy the M4 screws at any of your Ace Hardware stores for $.25 apiece compared to Gun stores and shops selling them for $2 each plus shipping.
What a ripoff!
-
thanks guys, that helps out.. Arndog- which model holasun red dot did you mount?
-
Holosun 507C with the ACSS reticle in green. ;D
-
Thanks! gonna give CZ custom a call today!
-
I've looked everywhere for one of these, and they are either out of stock or not compatible. I emailed CZC and haven't heard back on when they are expected back in stock. Does anyone have a line on one or looking to get rid of theirs?