The Original CZ Forum
CZ LONG ARMS => CZ Scorpion EVO => Topic started by: fisterkev on September 27, 2024, 02:56:16 PM
-
I recently re-acquired a Scorpion that I'd sold to someone a while back, and I've got a couple of questions since I've been out of the Scorpion for a couple of years. It's a EVO 3 S1 with a good number of modifications to it.
First question is on the mags. I know that the original mags are basically junk, most of the ones I had ended up with cracked feed lips, with one exploding on me when I picked the gun up, raining down 9mm all over the place, so those mags are out. This gun doesn't like PGS manticore mags but has always fed Magpuls and the PSA AK-V mags fine.
The question I have is whether any of the newer mags have also had feed lip issues, specifically the newer EVO 3+ mags. I'd like to know which are OK to leave loaded long-term.
Second question I have is about the striker block. I'm aware of the OOB issues, and while my bolt looks great and I've never experienced issues with this gun, I did notice that the striker block sits flush (I know it should be slightly elevated above the bolt), and the striker appears to move freely enough even when the block isn't depressed. I did order a Nexus striker block, and am wondering if that's likely to fix the issue. I'm not using a binary or bump.
Also what is going on with CZ USA? Are they going away, or what?
Thanks for any info.
-
New 3+ mags are GTG, but for the 3+ they are blind (unless that's changed). Mags are not fwd compatible.
MP mags are great, cheap and fit/feed in the 3+ but don't drop free.
ETS mags - 30 work, and 40 not so much.
I've never tried the Manticore mags.
I just make sure my FPS works. That's all.
-
I recently re-acquired a Scorpion that I'd sold to someone a while back, and I've got a couple of questions since I've been out of the Scorpion for a couple of years. It's a EVO 3 S1 with a good number of modifications to it.
First question is on the mags. I know that the original mags are basically junk, most of the ones I had ended up with cracked feed lips, with one exploding on me when I picked the gun up, raining down 9mm all over the place, so those mags are out. This gun doesn't like PGS manticore mags but has always fed Magpuls and the PSA AK-V mags fine.
The question I have is whether any of the newer mags have also had feed lip issues, specifically the newer EVO 3+ mags. I'd like to know which are OK to leave loaded long-term.
Second question I have is about the striker block. I'm aware of the OOB issues, and while my bolt looks great and I've never experienced issues with this gun, I did notice that the striker block sits flush (I know it should be slightly elevated above the bolt), and the striker appears to move freely enough even when the block isn't depressed. I did order a Nexus striker block, and am wondering if that's likely to fix the issue. I'm not using a binary or bump.
Also what is going on with CZ USA? Are they going away, or what?
Thanks for any info.
I haven’t had any issues with the BLACK OEM CZ Scorpion mags, they’re the best of the bunch from what I’ve seen. However, the CLEAR CZ OEM mags, have a reputation for being brittle / lousy. I don’t think the clear OEM mags are even made anymore.
Haven’t had any issues with the striker block. Was the previous owner using a binary trigger?
What’s wrong with CZ USA? Colt Management is the problem, they’re the King Midas of caca.
-
What’s wrong with CZ USA? Colt Management is the problem, they’re the King Midas of caca.
MAYBE CZ USA retained ALL of its leadership and booted the dopes from Colt.
However, we've seen some dumb going in so maybe not - or its just the vagaries of mergers.
I was part of a merger where the larger company supposedly merged, and the smaller, better company was to retain more leadership. In the end, it was only a shell till it was sold again 2 years later and enough of the bums stayed long enough to trash the merged company for a time. They were eventually booted, but they made life harder for enough folks. I left and praise be for that.
Mergers are hard.
-
What’s wrong with CZ USA? Colt Management is the problem, they’re the King Midas of caca.
MAYBE CZ USA retained ALL of its leadership and booted the dopes from Colt.
Yeah? NOPE.
Chris Bartocci knows Colt Mgt. from the inside…
https://m.youtube.com/watch?v=vs5Vd0_2fdE
-
What’s wrong with CZ USA? Colt Management is the problem, they’re the King Midas of caca.
MAYBE CZ USA retained ALL of its leadership and booted the dopes from Colt.
Yeah? NOPE.
Chris Bartocci knows Colt Mgt. from the inside…
https://m.youtube.com/watch?v=vs5Vd0_2fdE
Of course I was being facetious. Yes, so stupid not to remove the cancer.
-
Factory or magpul are the best quality. I’ve run the ETS clear mags in my scorpion and Kriss Vector. They seem fine on my scorp, my vector has a few feed issues.
-
If you have a EVO 3 S1, go with the PSA AKV mags. Cheap, plentiful, reliable with steel reinforced feed lips. I tried them all and stuck with the PSAs.
Right now blems are on sale. I bought several blems years ago and could not be happier!
https://palmettostatearmory.com/blem-psa-ak-v-9x19mm-u9-35-round-patterned-magazine-black.html#turnto_qa
-
If you have a EVO 3 S1, go with the PSA AKV mags. Cheap, plentiful, reliable with steel reinforced feed lips. I tried them all and stuck with the PSAs.
Right now blems are on sale. I bought several blems years ago and could not be happier!
https://palmettostatearmory.com/blem-psa-ak-v-9x19mm-u9-35-round-patterned-magazine-black.html#turnto_qa
Thanks for the link. Just ordered. They still seem to have plenty in both black and smoke.
-
PSA AKV mags are very good - but you will have to file down the tab in front considerably to have them drop free.
-
PSA AKV mags are very good - but you will have to file down the tab in front considerably to have them drop free.
I all depends on the PSA mag and the Scorpion. My first batch of PSA mags in my 1st gen Scorpion drop free. The second batch none drop free...Those are the only mags that do not drop free from mine. All my CZ, Manticore, MagPul, ETS drop free except the last PSA.
Steve
-
The ones that ran in the Evo S1 were "dual use" and are no longer available. https://palmettostatearmory.com/psa-scorpion-style-magazine-assembly-9x19mm-35rd-not-for-use-in-psa-ak-v.html
All the new ones I know of are NOT drop free from a Scorpion and in fact are hard to insert and extract. Sanding needed.