The Original CZ Forum
CZ PISTOL CLUBS => CZ Polymer Pistols: P10, P-07, P-09 => Topic started by: Rick53 on December 12, 2017, 02:04:07 PM
-
I see where I can buy the P10 C Mags with the Plus 2 extension to fit this P07 version : However the description under the standard P10C 15 Rounds says for P10C only. AM I to understand if I want a flush fit magazine for concealing I need to buy the standard P07 magazine that also works with duty? TY
-
The 15rd and 17rd P10c magazines will work with the P07, however the base plates are different. You will need to source flat and +2 base plates from a P07 and put them onto the P10c magazines if you want it to look right. CZ doesn?t sell them, I was able to source some from a member on this forum.
-
The 15rd and 17rd P10c magazines will work with the P07, however the base plates are different. You will need to source flat and +2 base plates from a P07 and put them onto the P10c magazines if you want it to look right. CZ doesn?t sell them, I was able to source some from a member on this forum.
So short of finding them like you did. I'm more or less stuck buying a P07 mag . At least one for concealment purposed : Appears we own the same gun based off your Avatar
-
My P-10C 15 round mags only have 1/16? gap between the top of the plate and the bottom of the grip on my P-07SR, and do not protrude past the bottom of the backstrap. My non-SR P-07 shipped with 15 round P-07 mags, so I don?t have any ?old style? mags for comparison, but I don?t see how it would affect concealability.
-
Here is mine, I sent it to Cajun and highly recommend it!
http://www.czfirearms.us/index.php?topic=81243.0 (http://www.czfirearms.us/index.php?topic=81243.0)
In regards to the fit of the P10c mags, they will fit ?flush?, but there will be a slight extension of the base plate at the front of the grip. If you don?t mind it, I would suggest picking them up. I ended up with the P07 flat and extended base plates because I did.
-
Here is mine, I sent it to Cajun and highly recommend it!
http://www.czfirearms.us/index.php?topic=81243.0 (http://www.czfirearms.us/index.php?topic=81243.0)
In regards to the fit of the P10c mags, they will fit ?flush?, but there will be a slight extension of the base plate at the front of the grip. If you don?t mind it, I would suggest picking them up. I ended up with the P07 flat and extended base plates because I did.
I'm sure cajun does good work. I went ahead and did my own following the sticky they put up on what to polish. Your posts don't say: What Hammer Spring and Recoil spring did they use?
-
(https://cajungunworks.com/wp-content/uploads/2015/07/Final-New-Website-w-mags-008.jpg)
Here is a picture from CGW?s website.
-
Yep that's the Kit I used : I also play around with the Blue hammer Spring and 15#Recoil : Haven't tried the extended firing pin yet. Haven't seem to need it. Like I said they do good work I'm sure. However most companies wouldn't put how to and what to polish in a Sticky Thread like they did. They even say what grits to you and where to polish the trigger bar . As detailed as that thread is I feel pretty confident I'm coming out with a finish Product very similar if not exactly like theirs. I've done several now for locals. Enough so that I am debating whether to advertise online. My wait times have been 24 hour turnarounds. Obviously not doing the number they are. Plus they are doing Milling and other work. I did 3 sets of sights last week in less then an hour.