The Original CZ Forum

CZ PISTOL CLUBS => CZ Polymer Pistols: P10, P-07, P-09 => Topic started by: dirkdiggler on January 24, 2018, 08:29:48 PM

Title: P-09 Safety not functioning properly.
Post by: dirkdiggler on January 24, 2018, 08:29:48 PM
Installed a short reset kit from Cajun Gun Works and had no issues getting everything back together except the safety. When I reinstalled the safety it wasn't engaging properly...engagement wasn't very positive. It could actually be pressed lower than the firing position. I ended up installing the decocker since that's what I run on all my other DA/SA guns but I;m curious what might have been done incorrectly by me.
Title: Re: P-09 Safety not functioning properly.
Post by: Slotback on January 24, 2018, 10:12:21 PM
When you were installing the safety did you leave the decocker spring in?
Title: Re: P-09 Safety not functioning properly.
Post by: M1A4ME on January 25, 2018, 06:30:27 AM
That left side safety should have a small spring and a small plastic piece that the spring pushes forward against the shaft of the safety.  That little piece is what gives you the "click" and holds the safety in position when you move the safety lever.

Sometimes that piece and the spring fall out/off when you remove the safety.  You have to be on the lookout for it and make sure you reinstall it if it does fall out.

Actually, look at TOK36's pictures.  The detent and spring push against a small "pin" that is out in front of the shaft and controls how far up/down the safety can be moved.
Title: Re: P-09 Safety not functioning properly.
Post by: dirkdiggler on January 25, 2018, 06:58:09 AM
Quote from: M1A4ME on January 25, 2018, 06:30:27 AM
That left side safety should have a small spring and a small plastic piece that the spring pushes forward against the shaft of the safety.  That little piece is what gives you the "click" and holds the safety in position when you move the safety lever.

Sometimes that piece and the spring fall out/off when you remove the safety.  You have to be on the lookout for it and make sure you reinstall it if it does fall out.

Bingo! I had actually found that piece when I was clearing my workbench (kitchen table) but initially thought it was from something else. Saved it so I'll be good to go if I ever want to reinstall the safety. Thanks
Title: Re: P-09 Safety not functioning properly.
Post by: Tok36 on January 25, 2018, 04:29:15 PM
A few pictures for reference.
(https://i.imgur.com/Nt2zE7e.jpg)

(https://i.imgur.com/htgIZsg.jpg)
Title: Re: P-09 Safety not functioning properly.
Post by: M1A4ME on January 25, 2018, 05:15:36 PM
Tok36, nice pictures.  I was wishing I'd taken some once or twice when I had mine apart, but nope.

Do you mind if a I "copy" one of yours for future use?
Title: Re: P-09 Safety not functioning properly.
Post by: Tok36 on January 25, 2018, 08:11:22 PM
Quote from: M1A4ME on January 25, 2018, 05:15:36 PM
Tok36, nice pictures.  I was wishing I'd taken some once or twice when I had mine apart, but nope.

Do you mind if a I "copy" one of yours for future use?

Not at all M1A4ME, please use any image that i post on the forums as you see fit.

Here are a few more that i nabbed a while back from Joe L if i remember correctly.

(https://i.imgur.com/adViXYg.jpg)

(https://i.imgur.com/GtYnseu.jpg)