The Original CZ Forum
CZ LONG ARMS => CZ Scorpion EVO => Topic started by: Xfrog on October 07, 2018, 01:47:41 PM
-
Here is mine. Just curious what kind of suppression you are getting and how you built it. I have 8 radial cones. Was running it on my sig but it getting gassed way too much.
-
Needs ceracoat(https://uploads.tapatalk-cdn.com/20181007/cc7f8170b9bb430efbf554494f891c94.jpg)
Sent from my SM-N950U using Tapatalk
-
I have a couple
Both are 7.6" 1.5" tubes. One all Ti with 6 Ti 60deg cones and 1 stainless. The other is all steel with 6 steel 60deg cones.
I used to run the Ti on the Scorpion but have decided to switch to using my rev 9 on the gun with tri lug and save my form 1's for rifle duty.
-
Does the rev 9 sound better??? I have a octane 9 and omega 300. The ti form 1 sounds better to me but of course it has more volume 7.5 x1.5
-
Yeah more volume in the Form 1 stuff than the Rev9. I went with the Rev 9 just to make range trips easier all around. I tend to take the scorpion and some 22lr pistols together alot. So just throwing tri lugs on all of them and using the Rev makes packing simple.
-
Had Taylor Pickerell "eMGunslinger" here on the forum shorten the barrel to 6.5", thread it 1/2x28 and install a 3-lug. I wanted more handguard space than the 4.5" K versions. Suppressors sit just inside a pistol length handguard. I prefer my cans outside the handguard for heat, weight, and ease of access. SilCo Octane 45 or Omega 9k with a Griffin 3-lug adapter. The griffin was shorter and had less wobble the older SilCo 3-lug adapter. I tried direct thread, but kept unscrewing the adapter from the can when trying to remove it from the barrel.
(https://1.bp.blogspot.com/-UrfPfHNMOqo/WcMUZuGq5dI/AAAAAAAABM4/jNP86j6v4EoGZM6_nFGIxKilqBNSXh1WwCLcBGAs/s1600/IMG_4451.JPG)
(https://1.bp.blogspot.com/-ifCfXN-5Wr0/WcMUY5TzAYI/AAAAAAAABMw/i2p4myLvfX4S9WXBJLzBgbV4fTywMQ16ACLcBGAs/s1600/IMG_4446.JPG)
(https://1.bp.blogspot.com/-65NolCuOu_s/WcMUY32QFFI/AAAAAAAABMs/N0Gvk7iC7yIPaNWb9SI0oWUQXbLNwKYXQCLcBGAs/s1600/IMG_4448.JPG)
-
That's a problem I am having too. Direct thread to keep it short but worried if I rocket it the adapter may come out of the can when trying to remove it. May end up cutting the barrel down another 2 inches and getting a taper mount
-
(https://image.ibb.co/bHzRFf/CZ-Scorpion-Obsidian-9.png) (https://imgbb.com/)
Using a Rugged Obsidian 9 in K config
-
I have heard that rugged obsidian on a 9mm AR. Nice sounding can.
Sent from my SM-N950U using Tapatalk
-
My form 1 and SBR setup:
(https://i.imgur.com/JkXLKfVl.jpg)
(https://i.imgur.com/rqqIG4Sl.jpg)
-
My form 1 and SBR setup:
(https://i.imgur.com/JkXLKfVl.jpg)
(https://i.imgur.com/rqqIG4Sl.jpg)
Did you make a lower that accepts glock mags?
-
(https://i.imgur.com/rqqIG4Sl.jpg)
Did you make a lower that accepts glock mags?
Exactly what I want to know!
-
(https://i.imgur.com/rqqIG4Sl.jpg)
Did you make a lower that accepts glock mags?
Exactly what I want to know!
Following!
-
Did you make a lower that accepts glock mags?
Yes. I posted most of the pics on the FB group. Some of the pics are on an old instagram, thekettlebellgunsmith. Sorry to say, it's a one-off project. I do it for a hobby. Only made one and not planning to sell it. Reached out to Manticore arms to see if they wanted any of the measurements and don't believe they were interested at the time.
-
Did you make a lower that accepts glock mags?
Yes. I posted most of the pics on the FB group. Some of the pics are on an old instagram, thekettlebellgunsmith. Sorry to say, it's a one-off project. I do it for a hobby. Only made one and not planning to sell it. Reached out to Manticore arms to see if they wanted any of the measurements and don't believe they were interested at the time.
What did you do to the bolt to make it happy with single feed mags?
-
Did you make a lower that accepts glock mags?
Yes. I posted most of the pics on the FB group. Some of the pics are on an old instagram, thekettlebellgunsmith. Sorry to say, it's a one-off project. I do it for a hobby. Only made one and not planning to sell it. Reached out to Manticore arms to see if they wanted any of the measurements and don't believe they were interested at the time.
Wow, this seems like a much better project than a bullpup conversion, from a consumer interest standpoint... People would jump at the opportunity to buy a simple lower that allows for Glock mags.
-
Did you make a lower that accepts glock mags?
Yes. I posted most of the pics on the FB group. Some of the pics are on an old instagram, thekettlebellgunsmith. Sorry to say, it's a one-off project. I do it for a hobby. Only made one and not planning to sell it. Reached out to Manticore arms to see if they wanted any of the measurements and don't believe they were interested at the time.
Wow, this seems like a much better project than a bullpup conversion, from a consumer interest standpoint... People would jump at the opportunity to buy a simple lower that allows for Glock mags.
But then the magazines they make would be obsolete.
-
But then the magazines they make would be obsolete.
Only if you bought the modified lower... The original Scorpions would still use the CZ mags.
-
What did you do to the bolt to make it happy with single feed mags?
Milled it with a 60? end mill. Took off the minimum amount so that section of the bolt would fit in a stock Glock mag that's metal lined. Magpul's have more clearance.
(https://i.imgur.com/60EoQc8h.jpg)