The Original CZ Forum

CZ PISTOL CLUBS => CZ Polymer Pistols: P10, P-07, P-09 => Topic started by: CZ-TCP on May 13, 2019, 07:50:00 PM

Title: +1 Mag Extension for the P-10s
Post by: CZ-TCP on May 13, 2019, 07:50:00 PM
Is anyone making a +1 mag extension for the P-10 S?


[Mods clarified title for future searches]
Title: Re: +1
Post by: joedirt199 on May 13, 2019, 08:47:04 PM
If you want one more round, cut off the legs of the follower. Will get you +1 with stock spring.
Title: Re: +1
Post by: Yelm on May 16, 2019, 02:08:11 AM
Better question- is anybody making a P10S? 
Title: Re: +1
Post by: CZ-TCP on May 16, 2019, 10:10:44 PM
I got one but would like a little more room for my pinky and an extra round.
Title: Re: +1 Mag Extension for the P-10s
Post by: Yelm on May 21, 2019, 06:22:46 AM
https://gallowayprecision.com/cz/p-10c/plus-2-mag-extension-for-cz-p10c-pistols/

A +2 should give you the pinky room. 
Title: Re: +1
Post by: sfost24688 on May 21, 2019, 11:44:31 PM
If you want one more round, cut off the legs of the follower. Will get you +1 with stock spring.

Does this cause any kind of issues ? Feeding ?
Title: Re: +1 Mag Extension for the P-10s
Post by: Dj1001 on May 22, 2019, 11:17:15 PM
The CZ +2 mag plate for the p09 is a perfect fit on p10s magazines. Part #0722-0770-02ND

I bought the extensions from HB industries.
https://hbindustries.net/store/shop/cz-p07p09p10-magazine-2-base-pad/

(https://i.imgur.com/GDFKmCU.jpg)

Mags hold 14 rounds easily, and allow for a full grip.

(https://i.imgur.com/VChZkWJ.jpg)

I dont have a ton of range time with them but over a few hundred rounds they have been flawless.
Title: Re: +1 Mag Extension for the P-10s
Post by: joedirt199 on May 23, 2019, 12:40:44 AM
No feeding issues with stock modified follower. Just have to round the front left corner of the follower because as you load about 5 rounds the follower tilts and gets hung up on the magazine release holes. Round the sharp edge made by cutting off the legs and no more hang-up. You can load a full mag and let it sit to make seating a fully load mag on a closed slide easier. Have shot several mags in my p09 and sp01 shadow with no feesing problems and working slide lock on empty. Grams followers and springs will not lock the slide back regularly.
Title: Re: +1 Mag Extension for the P-10s
Post by: asssets on April 12, 2021, 07:11:35 AM
I cannot find a video I watched, but the main point of +1 base used was it was not adding size at the back (not going past a grip).  I think it was shielded arms, but they carry only +5 now. There was also hyve extension, but it was bigger.
Similar to https://www.thingiverse.com/thing:4040124 (https://www.thingiverse.com/thing:4040124), but +1 made of aluminum. And it was a blue in color.
Also CZ custom make similar, but not +1 https://www.cz-parts.com/cz-p-10-extended-mag-pad-aluminium (https://www.cz-parts.com/cz-p-10-extended-mag-pad-aluminium)
Maybe someone knows what I'm talking about and can provide more info on that.

PS: NO surprise I could not find it, because it was a video about a Glock
But the main point is the same, adding support for the pinky finger.

https://youtu.be/kl2kMvonO0I (https://youtu.be/kl2kMvonO0I)
Title: Re: +1 Mag Extension for the P-10s
Post by: Bigkev on April 22, 2021, 06:17:21 PM
I have the HBI +2 extensions on all of my mags. They work great.


Sent from my iPhone using Tapatalk
Title: Re: +1 Mag Extension for the P-10s
Post by: gwes351 on April 22, 2021, 07:11:47 PM
Apparently there is a +1 aluminum extension you can order (special order it seems) from CZ parts (direct from the CZ factory store).   It is quite pricey, but is out there.  CZ parts also has just a pinky extension, no + rounds, as well - again, aluminum and quite pricey - I recently ordered 2 of these to try.  Leapers /UTG also makes a + 0 extension - but it appears out of stock everywhere.   This is what I've found from my research on it so far.
Title: Re: +1 Mag Extension for the P-10s
Post by: Hammer Time on April 24, 2021, 03:58:46 PM
I really just want a minimal pinky extension for the flush fit mag - I'm fine with the standard 12+1 capacity (I carry a +2 mag as a spare), and I've tried a number of different options at this point. I figured I'd share my results so far, to help others who may be looking for the same:

Springer Precision .375" basepad (+0)

(https://imagizer.imageshack.com/v2/800x600q90/922/9uBDlb.jpg)

Nicely made, but as you can see, it's designed to work with their magwell (which is not clear in their product description), and is a pretty terrible fit otherwise, both in terms of the gap and the fit at the front of the grip which isn't even close to being flush.

Distance from bottom of grip to bottom of basepad:

(https://imagizer.imageshack.com/v2/800x600q90/922/L5mwTD.jpg)

Killer Innovations P10 basepad (+0)

(https://imagizer.imageshack.com/v2/800x600q90/923/FgGVJc.jpg)

I really wanted to like this one, but as you can see, it's also designed to work with their proprietary basepad and is a terrible fit otherwise. I wish they were clear about this on their product description and/or showed pics of it installed on the pistol. If they would just offer a flush fit version of this that offered the same distance from the bottom of the grip to the bottom of the basepad (essentially just fill the gap) this one would be a great option, imo.

Distance from bottom of grip to bottom of basepad:

(https://imagizer.imageshack.com/v2/800x600q90/924/ryVHWY.jpg)

Henning Group EDC Magazine Grip Extension (+2)

(https://imagizer.imageshack.com/v2/800x600q90/923/5Gryqd.jpg)

As you can see, this option is an excellent fit on the P-10S and the quality is top-notch. No gap and flush fit at the front. It uses a retaining screw on the backside of the basepad that makes it lock up solid with the magazine. I'm not crazy about the glossy finish, and as I said above, I'd rather just have a pinky extension for a little more minimal grip profile, but so far this is the best option I've seen for a little bit more real estate for your pinky.

Distance from bottom of grip to bottom of basepad:

(https://imagizer.imageshack.com/v2/800x600q90/922/gfUCTd.jpg)

For comparison, here is the distance from the bottom of grip to the bottom of basepad using the flush fit CZ plastic basepad:

(https://imagizer.imageshack.com/v2/800x600q90/924/i9MAr1.jpg)

And the distance from the bottom of grip to the bottom of basepad using the +2 CZ plastic basepad:

(https://imagizer.imageshack.com/v2/800x600q90/923/QRw5J4.jpg)

So far, the Henning Group basepad is the one I've found that fits the bill the best, and if it gives me two more rounds while still being almost .2" inches shorter than the OEM +2 basepad, I'll take it. But what I really want for the P-10S is something akin to what Armory Craft offers for the P365/XL:

(https://imagizer.imageshack.com/v2/800x600q90/924/IUEDLu.jpg)