« previous next »
Pages: [1]   Go Down

Author Topic: CZ 50 trigger return spring woes  (Read 4853 times)

0 Members and 1 Guest are viewing this topic.

Offline bregma

  • Jr. Member
  • **
  • Posts: 25
CZ 50 trigger return spring woes
« on: September 23, 2018, 04:32:50 PM »
Snagged a really nice early production CZ 50 a little while back.  It quickly became one of our favorite small caliber shooters.  At the range yesterday, apparently  the trigger spring broke- if I manipulate the gun around  the trigger will still work but there is no trigger reset.  Been scouring the internet to no avail-any ideas where one could be found? Lots of parts, but trigger springs seem nonexistent. Any help would be greatly appreciated.
Logged

Offline rdcinhou

  • Hero Member
  • *****
  • Posts: 1817
  • Coat of Arms for Uherský Brod
Re: CZ 50 trigger return spring woes
« Reply #1 on: September 23, 2018, 05:43:42 PM »
The CZ 50 and CZ 70 share most of the same parts, so you might widen your search.

I see that Numrich is out of stock for this part (#29) for both the 50 and 70.

I also looked at Schluder Shots (Round Rock, TX) https://www.schludershots.com as he lists a bunch of the 70 parts, but this is one part that he doesn't have listed on his website.  You might write to him--he might know where to find one.

Good Luck!
Logged
CZ24/27/38/40P/45/52, Vzor 50/70,75BΩ,75D Compact,P01/07/09,P10M/S/C/F(9mm,.45), Phantom,SP01 Tactical,Shadow 2 (Blue,Urban Gray), 82/83/85 PreB, 97BE,97BD,97BDE,100,1911A1, 2075D RAMI,452 American,550 Urban Counter Sniper,805 Bren S1,Drake G2,Duo,Z,vz24 8mm Mauser,FK 7.5 BRNO Field Pistol, PSD

Offline bregma

  • Jr. Member
  • **
  • Posts: 25
Re: CZ 50 trigger return spring woes
« Reply #2 on: September 23, 2018, 08:10:07 PM »
I have tried every which way including looking for parts guns cz50 and 70 as well.  I will give schluder shots a call- I found them in my search as well. Thank you for the input.
Logged

Offline MilfordBauer

  • Jr. Member
  • **
  • Posts: 74
Re: CZ 50 trigger return spring woes
« Reply #3 on: October 31, 2018, 09:40:07 PM »
buymilsurplus.com and apexgun parts use to carry a lot of CZ70 parts.  Numrich you had to watch because they would ship used parts.  Make sure it is NOS(new old stock)
Logged

Offline bregma

  • Jr. Member
  • **
  • Posts: 25
Re: CZ 50 trigger return spring woes
« Reply #4 on: November 02, 2018, 03:13:23 AM »
I have e-mailed everyone I could think of with no luck so far.  I did recently get a hold of a well stocked cz 52 armorers kit and one of the springs looks very close to me, but I am a little reticent to tear the side plate off without being sure. I have read numerous posts of the sear spring falling out of orientation and not being easy to figure out how it goes back.   Its a shame because its a pretty darn early one, less than a thousand from the first one as far as I can tell. Thanks for the input,hopefully I will get lucky one of these times!
Logged

Offline bregma

  • Jr. Member
  • **
  • Posts: 25
Re: CZ 50 trigger return spring woes
« Reply #5 on: December 08, 2018, 02:09:46 PM »
Finally found a  correct trigger spring for the old girl.  Now I just have to get up the gumption to tear the gun apart.  Any body have any words of advice?  I'm really excited to get it working again.  I have noticed  recently on gunbroker  a couple really nice ones of these going for $600.00 or close to it- couldn't believe it, but that makes me feel a little better about what it cost to get the spring I needed! Thanks again - the CZ forum rocks!
Logged

Offline film495

  • Newbie
  • *
  • Posts: 5
Re: CZ 50 trigger return spring woes
« Reply #6 on: July 18, 2019, 11:57:56 AM »
also in same boat, curious if you can share where you found spring?
Logged

Offline bregma

  • Jr. Member
  • **
  • Posts: 25
Re: CZ 50 trigger return spring woes
« Reply #7 on: July 19, 2019, 10:29:02 PM »
It's really difficult to find trigger springs for these.  I finally found one on eBay after a lot of looking.  Good luck.
Logged

Offline film495

  • Newbie
  • *
  • Posts: 5
Re: CZ 50 trigger return spring woes
« Reply #8 on: July 19, 2019, 11:49:48 PM »
still haven't found one, decided it can't be that hard to bend that spring so ordered some wire, we'll see ..
Logged

Offline NickySantoro

  • Jr. Member
  • **
  • Posts: 61
Re: CZ 50 trigger return spring woes
« Reply #9 on: December 13, 2019, 04:18:59 PM »
For anyone with interest in the 50 or 70, search santaroga surplus on you tube
Logged
Pages: [1]   Go Up
« previous next »