« previous next »
Pages: [1]   Go Down

Author Topic: New stainless shoots a bit left  (Read 1812 times)

0 Members and 1 Guest are viewing this topic.

Offline Warpspasm

  • Full Member
  • ***
  • Posts: 181
New stainless shoots a bit left
« on: November 14, 2012, 09:50:54 PM »
I've now put about 200 rounds through my brand new, beautiful polished stainless 75B. It's very accurate, but at 10 yards it shoots about 1.5" left and a wee bit high. I'm thinking about drifting the rear sight a bit to the right, but I noticed the rear sight has been staked. Have any of you drifted your sights? If so, how much force did it take to get past the staking? Did you re-stake after you made the adjustment?
Logged
Dolor Temporarius
Gloria Aeterna
Cicatrices Virginibus Placent

CZ 24, CZ 52, CZ 82 (2), CZ 75B, Pre-B, P-09, P-01 UG, Shadow 2, Kadet upper, 455 Tacticool, 912 12ga, Scorpion Carbine - Still need a CZ 38 & CZ 70

Offline DenStinett

  • Hero Member
  • *****
  • Posts: 6464
  • HALT, Who goes there?
Re: New stainless shoots a bit left
« Reply #1 on: November 15, 2012, 04:03:05 AM »
It does take a bit of encouragement, but it will go
If you don?t have a Sight Pusher use a Nylon or Teflon Punch
Brass if you don?t have either of the other two
Logged
So tell me again how Trump was worse then the 8 years before .... AND what's coming after HIM !

Offline Warpspasm

  • Full Member
  • ***
  • Posts: 181
Re: New stainless shoots a bit left
« Reply #2 on: November 15, 2012, 06:34:29 AM »
Quote from: DenStinett on November 15, 2012, 04:03:05 AM
It does take a bit of encouragement, but it will go
If you don?t have a Sight Pusher use a Nylon or Teflon Punch
Brass if you don?t have either of the other two

I do have a nylon tipped punch. Did you stake your sight again after you moved it?
Logged
Dolor Temporarius
Gloria Aeterna
Cicatrices Virginibus Placent

CZ 24, CZ 52, CZ 82 (2), CZ 75B, Pre-B, P-09, P-01 UG, Shadow 2, Kadet upper, 455 Tacticool, 912 12ga, Scorpion Carbine - Still need a CZ 38 & CZ 70

Offline DenStinett

  • Hero Member
  • *****
  • Posts: 6464
  • HALT, Who goes there?
Re: New stainless shoots a bit left
« Reply #3 on: November 16, 2012, 12:23:49 AM »
Quote from: Warpspasm on November 15, 2012, 06:34:29 AM
Did you stake your sight again after you moved it?
It's not really needed
Still; Make a note of where the Sight Notch aligns with the Slide's Top Serrations
Watch to see if there's any visible movement over time
Logged
So tell me again how Trump was worse then the 8 years before .... AND what's coming after HIM !

Offline firecracker6

  • Full Member
  • ***
  • Posts: 357
Re: New stainless shoots a bit left
« Reply #4 on: December 01, 2012, 04:32:57 PM »
Have you tried some dummy rounds to make sure it's not you first?  I'm not trying to insult you or anything but most problems like this are user error.
Logged

Offline Warpspasm

  • Full Member
  • ***
  • Posts: 181
Re: New stainless shoots a bit left
« Reply #5 on: December 01, 2012, 09:13:47 PM »
Quote from: firecracker6 on December 01, 2012, 04:32:57 PM
Have you tried some dummy rounds to make sure it's not you first?  I'm not trying to insult you or anything but most problems like this are user error.

I'm actually an pretty experienced pistol shooter. Not that it still couldn't be me :)  But, as it turned out, it was indeed the sights. I drifted them a hair and now things are just fine. Not too crazy about the trigger though. I might have to read up on what others are doing to their triggers.
Logged
Dolor Temporarius
Gloria Aeterna
Cicatrices Virginibus Placent

CZ 24, CZ 52, CZ 82 (2), CZ 75B, Pre-B, P-09, P-01 UG, Shadow 2, Kadet upper, 455 Tacticool, 912 12ga, Scorpion Carbine - Still need a CZ 38 & CZ 70

Offline firecracker6

  • Full Member
  • ***
  • Posts: 357
Re: New stainless shoots a bit left
« Reply #6 on: December 02, 2012, 09:58:05 AM »
One can't argue w/ success.  There is lots of good info on this forum about how to improve the trigger.  If you're going to carry you might look into a hammer from CGW, if it's for comp. you might try the comp. hammer from czcustom; I think CGW makes some comp stuff too.
Logged
Pages: [1]   Go Up
« previous next »