« previous next »
Pages: [1]   Go Down

Author Topic: SP-01 guide rods.  (Read 2511 times)

0 Members and 1 Guest are viewing this topic.

n-12-Volt-Man-czechpistols82792

  • Guest
SP-01 guide rods.
« on: May 03, 2005, 08:21:19 AM »
BIL and I made up a couple of prototype SP-01 Guide Rods last night.  They will be tested within the next week for proper fit.  After that, if all goes well, they will be available for purchase through JackAsh Custom.

See pictures here.
CLICK HERE
Logged

Offline avordman

  • Newbie
  • *
  • Posts: 20
SP-01 guide rods.
« Reply #1 on: March 22, 2007, 05:42:41 PM »
I am interested in the stainless steel guide rods, but when I try to go to the Jack Ash Custom website I am told that the page is not available. Can someone help me out? Am I doing something wrong or has the website changed?

Thanks,
avordman
Logged

mbott

  • Guest
SP-01 guide rods.
« Reply #2 on: March 22, 2007, 08:11:34 PM »
Suggest you look elsewhere for your guide rod.  Jack Ash is history and has been for a while.

--
Mike
Logged

Offline William Chase

  • Administrator
  • Hero Member
  • *****
  • Posts: 1570
SP-01 guide rods.
« Reply #3 on: March 23, 2007, 07:52:14 AM »
Steve Bedair, of Steve Bedair's Websites, is working on one, but hasn't been satisfied with the results yet. Lots of folks here are quite pleased with his other work, and his customer service.

Bill
Logged
"The right to buy weapons is the right to be free". A.E van Vogt
CZ75 P-01   CZ52 (53)  S&W 642  
1903 M96B Carl Gustaf Swedish Mauser Remington 870 Wingmaster 12Ga
USPSA Area 4, Brazosland Pistoleros

Offline Jeroenw114

  • Full Member
  • ***
  • Posts: 108
SP-01 guide rods.
« Reply #4 on: March 25, 2007, 05:03:50 AM »
I see a lot of questions after guide rods but after all it is a very easy job for one with a lath. Make a drawing of the original, make the front part smaller (otherwise it jams) and ask someone with a lath to make on.
I made one of SS for my CZ 75 SA.

Greetings,
Jeroen
Logged

mbott

  • Guest
SP-01 guide rods.
« Reply #5 on: March 25, 2007, 01:32:22 PM »
This is the pin I started with when I replaced the factory guide rod in my 40P.  Kinda wish I ordered a extra one to see if it would fit/work in the SP-01.  

MSC Direct

The description reads: Metric Nitride Ejector Pins
Pin Diameter: 5.0 mm
Overall Length: 100 mm
Head Diameter: 10.0 mm
Head Height: 3.0 mm

The rough dimensions of the factory guide rod I measured was:
Pin Diameter: 4.78 mm
Overall Length: 97 mm
Head Diameter: 10.0 mm
Head Height: <no measurement taken>

Pretty close.

--
Mike
 
Logged

n-604shooter-czechpistols82792

  • Guest
SP-01 guide rods.
« Reply #6 on: April 02, 2007, 12:30:47 PM »
Does anybody know if Steve Bedair is any closer to getting one made? By the way, whatever happened to Jackash Custom? His site is no longer available.
Logged

mbott

  • Guest
SP-01 guide rods.
« Reply #7 on: April 02, 2007, 12:59:54 PM »
Quote
Quote:
Does anybody know if Steve Bedair is any closer to getting one made?


Not the last time I looked at his website.

Quote
Quote:
By the way, whatever happened to Jackash Custom? His site is no longer available.


There are too many threads on the various boards here and at CZ Shooters.  Should take about 5 minutes to discover all the people that had issues with Jack Ash.  To bad, too.

--
Mike
Logged

Offline Mike Russell

  • Full Member
  • ***
  • Posts: 154
SP-01 guide rods.
« Reply #8 on: April 02, 2007, 02:23:25 PM »
When I emailed him recently, he said he'd had a few prototypes but still isn't happy with the results.  He's still working on it though.  If you email him with your interest, he will keep you updated on the progress.
Logged
Pages: [1]   Go Up
« previous next »