Optic milling for suppressor ready p10c

[iamjocanadian]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

[Edward_Teach]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

I can't answer for the second part but for the first. Yes people have had their slides milled for the RMR both in front and behind the rear sight (most of them if not all have had a new dovetail milled for glock rear sights)

[s0nspark]

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

Whether mounting BUIS in front or behind the optic, a new dovetail is almost certainly necessary and, yes, the optic will require that the extractor pin be shortened.

Choice of optic may change the particulars slightly.

[Raining_Brass]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

There is enough room.
Extractor retaining pin will need to be trimmed down after. Won't hurt anything.

[iamjocanadian]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

I can't answer for the second part but for the first. Yes people have had their slides milled for the RMR both in front and behind the rear sight (most of them if not all have had a new dovetail milled for glock rear sights)

I would imagine that the new cut was primarily to add suppressor height sights to co-witness with the dot whereas the factory sights on this gun already would meet that requirement.

[s0nspark]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

I can't answer for the second part but for the first. Yes people have had their slides milled for the RMR both in front and behind the rear sight (most of them if not all have had a new dovetail milled for glock rear sights)

I would imagine that the new cut was primarily to add suppressor height sights to co-witness with the dot whereas the factory sights on this gun already would meet that requirement.

Yes, that is for suppressor-height sights.

Yours is a suppressor-ready model?

[s0nspark]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

There is enough room.
Extractor retaining pin will need to be trimmed down after. Won't hurt anything.

Good to know, Bruce!

Do you have pics of this with the stock CZ suppressor-height sights? Just wondering how far forward the optic sits...

Also, is this only true for the RMR?

[Raining_Brass]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

There is enough room.
Extractor retaining pin will need to be trimmed down after. Won't hurt anything.

Good to know, Bruce!

Do you have pics of this with the stock CZ suppressor-height sights? Just wondering how far forward the optic sits...

Also, is this only true for the RMR?

P-10C is long enough for any optic to fit in front the dovetail. Although long optics like Venom and FF III do cut it close. I'd recommend Viper or RMR.

[iamjocanadian]

Hell again all,

I had grand plans to have my p10c milled here in Canada for an RMR. The company that will be doing the work was the Canadian warranty depot for CZ until recently but has not yet worked on a p10.

First question, is there enough space between the factory rear sights and ejection port for the RMR?

Secondly, do I need to worry about the slide cut messing with the extractor pin?

There is enough room.
Extractor retaining pin will need to be trimmed down after. Won't hurt anything.

Good to know, Bruce!

Do you have pics of this with the stock CZ suppressor-height sights? Just wondering how far forward the optic sits...

Also, is this only true for the RMR?

P-10C is long enough for any optic to fit in front the dovetail. Although long optics like Venom and FF III do cut it close. It's recommend Viper or RMR.

Great info. Thank you sir.

[s0nspark]

P-10C is long enough for any optic to fit in front the dovetail. Although long optics like Venom and FF III do cut it close. It's recommend Viper or RMR.

Good to know - thanks!

[Dirk]

I had mine machined in Wichita, KS.

Trijicon RM06 sits so low in the slide that I get a lower 1/3 co-witness with the factory height (not suppressor) sights.

LOVE it!

[rch024]

I had mine machined in Wichita, KS.

Trijicon RM06 sits so low in the slide that I get a lower 1/3 co-witness with the factory height (not suppressor) sights.

LOVE it!

Could you post some pics of this?  I'd be interested to see that setup.  I'm sold on an RMR, just waiting to decide which pistol it will go on first!