Author Topic: 13# Main Spring Binding In Steel Compact  (Read 343 times)

0 Members and 1 Guest are viewing this topic.

Offline CZJ

  • Jr. Member
  • **
  • Posts: 95
13# Main Spring Binding In Steel Compact
« on: October 29, 2018, 10:47:01 PM »
 I have the blue 13-pound mainspring kit installed in my steel compact. It seems like it's binding up by the noise it makes when it's installed and you squeeze the trigger, like a creaking noise. Broke it all down tonight to clean and inspect and found that the spring seems like it's binding because the paint is rubbed off on one side and the spring appears bent compared to the factory new one I have. I didn't notice before when I installed it but I noticed that this blue spring is a coil or two longer then the factory spring, what gives? Compact and full-size mainspring different? This was ordered from CGW. For now I just put the stock Springs back in it, any help would be appreciated, thanks.

http://i.imgur.com/pYATLtc.jpg

Offline Scarlett Pistol

  • Hero Member
  • *****
  • Posts: 3154
Re: 13# Main Spring Binding In Steel Compact
« Reply #1 on: October 29, 2018, 11:00:27 PM »
In haven?t had that happen before. Curious to see what others say to trouble shoot. If no one chimes in I?d call CGW. They are super nice and helpful.
"In God I trust. All others must supply data."

Online Stuart

  • Hero Member
  • *****
  • Posts: 8342
Re: 13# Main Spring Binding In Steel Compact
« Reply #2 on: October 30, 2018, 11:47:00 AM »
could clip a coil or two and be set.

full size and compact use same mainspring. plugs are different size to account for the difference in frame size.
stuart@czcustom.com
czcustom.com

Offline rhart

  • Hero Member
  • *****
  • Posts: 1992
Re: 13# Main Spring Binding In Steel Compact
« Reply #3 on: October 30, 2018, 12:35:54 PM »
If the hammer strut is rough it will cause this. Try smoothing the strut - polishing/smoothing the nicks/ridges. Smooth out the tip of the strut as well.
Musashi:
- In all forms of strategy, it is necessary to maintain the combat stance in everyday life and to make your everyday stance your combat stance. (situational awareness).
- You can only fight the way you practice.
- If you do not control the enemy, the enemy will control you.

Offline The Guardian

  • Full Member
  • ***
  • Posts: 292
  • CZ dreamin'... zzzzzzz..... don't wake me
Re: 13# Main Spring Binding In Steel Compact
« Reply #4 on: October 30, 2018, 06:44:04 PM »
Not sure what grips or grip screws your using.......thin grips with longer grip screws?  The longer screws can hinder/rub on the mainspring during trigger pull....if that's the case, shorter grip screws may be in order.......just brain-storming here  ::)
“I won't be wronged, I won't be insulted, and I won't be laid a hand on. I don't do these things to other people, and I require the same from them."  John Wayne as J.B Books in "The Shootist" 1976

Offline M1A4ME

  • Hero Member
  • *****
  • Posts: 4900
  • I've shot the rest, I now own the best - CZ
Re: 13# Main Spring Binding In Steel Compact
« Reply #5 on: October 30, 2018, 07:22:25 PM »
The spring will rub a corner (strut has four, so there's a lot of opportunity there) and hang (just a bit) before popping loose to hang again and pop loose again.

My old Pre CZ85's strut actually has a washboard looking corners on it.  The spring rubbed so many years, so much, that it wore ridges in the corners.

You don't notice it when firing the pistol but if you manually cock it you'll hear it.

You can, as someone suggested, polish those 4 corners to smooth up the spring coils movement up/down the strut.

Make sure your pistol is empty, remove on grip panel, manually cock the hammer and listen to it.  Watch it, too.  You might see the spring sort of jerk/bounce as the spring is slowly compressed.  That'll tell you to polish those four corners on the struck.

Or, as suggested by another poster, it might allow you to see if the spring is rubbing the end of the grip screw on the opposite grip.  If not, reinstall the grip panel you removed and take the other one off and cock it to see if the other side is contacting the end of that grip's screw.

Good luck with it.
Better to have it and not need it, than to need it and not have it.  So, if you see me walking the dogs with my SIG 556R, its okay.

 

anything