Author Topic: New P-10 CGW GEN II Trigger  (Read 1950 times)

0 Members and 1 Guest are viewing this topic.

Offline HST

  • Full Member
  • ***
  • Posts: 178
Re: New P-10 CGW GEN II Trigger
« Reply #30 on: November 30, 2018, 06:41:52 AM »
What you see as stripes are the different layers that make up the material . 
P 10
75 B SAO
Browning Hi Power
G 43
Colt 1911 70 series

Offline dpsk

  • Jr. Member
  • **
  • Posts: 73
Re: New P-10 CGW GEN II Trigger
« Reply #31 on: December 02, 2018, 02:57:28 PM »
Has anyone tried this Gen II trigger yet?  If so, impressions please...

Offline Indy_Tim

  • Sr. Member
  • ****
  • Posts: 633
Re: New P-10 CGW GEN II Trigger
« Reply #32 on: December 03, 2018, 07:57:41 AM »
Has anyone tried this Gen II trigger yet?  If so, impressions please...
Not yet.  Both of my P10Cs already have the triggers done, so I’m waiting for the P10S to do one of these.


Sent from my iPad using Tapatalk

Offline Dan-O

  • Jr. Member
  • **
  • Posts: 43
Re: New P-10 CGW GEN II Trigger
« Reply #33 on: December 03, 2018, 10:28:11 AM »
I have one en route for my new F.....

Offline RandyMan

  • Full Member
  • ***
  • Posts: 123
Re: New P-10 CGW GEN II Trigger
« Reply #34 on: December 03, 2018, 03:27:37 PM »
Installing my CGW GenII trigger tonight. I will let you know how it is.

Offline ViperM

  • Jr. Member
  • **
  • Posts: 34
Re: New P-10 CGW GEN II Trigger
« Reply #35 on: December 03, 2018, 09:31:13 PM »
I installed mine yesterday.  It's comfortable.  The trigger was a little tight.  Polished the trigger bar and lubed it to loosen it up.

Offline njbren

  • Newbie
  • *
  • Posts: 14
Re: New P-10 CGW GEN II Trigger
« Reply #36 on: December 04, 2018, 10:23:04 PM »
Just finished installing mine, I also had to polish the trigger bar around the trigger pin. It was tight and rubbed hard on the trigger. It definitely shortened the pull and reset! I just need to get out and shoot. Hoping this minimizes the bite as well

Offline Indy_Tim

  • Sr. Member
  • ****
  • Posts: 633
Re: New P-10 CGW GEN II Trigger
« Reply #37 on: December 05, 2018, 02:54:07 PM »
I already have a sit of Night Fision sights inbound for the long awaited P10S.  I really should go ahead and order the CGW goodies for it while waiting too.

Offline earlan357

  • Full Member
  • ***
  • Posts: 367
Re: New P-10 CGW GEN II Trigger
« Reply #38 on: December 10, 2018, 11:13:02 PM »
Mine was tight as well.  The pin holes were fine, but the inside corners of the trigger were rubbing against the trigger bar.  I scraped away the offending material with a 1/8" punch and voila. 






I'm working on a video review but need the snow to melt so I can get a few hundred rounds downrange. In the meantime here's a comparison GIF. Green is the trigger at rest, Yellow is the "Wall", and Red is the end of travel. As you can see, the triggers don't change the characteristics of the OEM trigger much beyond shortening pre-travel. Weight is largely the same too. The major difference is ergonomics. The flat profile of the HBI feels better when using the pad of your finger. People with longer fingers will appreciate this. The CGWs are flat in the middle third (the flat portion of the G10 is wider) and rounded on the sides making pulling with the first joint more comfortable. The curve also encourages pulling higher up, away from the trigger guard. This makes for a slightly heavier, but crisper feeling trigger and helps prevent "pinch", when the skin of the trigger finger rolls under the tip of the trigger and gets pinched between the frame. The safety blade of the Gen2 is also flush with the tip of the trigger, further reducing risk of pinch. In hot weather, I've noticed my aluminum triggers getting uncomfortably hot after extended shooting. The G10 material should be better in this regard but I won't know until the temperatures reach above 90 again. Finally, unlike the Gen1 trigger, the Gen2 safety lever spring is captured, so it won't fly loose if the adjustment screw is lost or unscrewed too far.


Offline Earl Keese

  • Hero Member
  • *****
  • Posts: 2851
Re: New P-10 CGW GEN II Trigger
« Reply #39 on: December 11, 2018, 07:12:09 AM »
Looks to be a nice improvement over the gen1. Nice write up earlan, that answers a lot of questions people ask.

Offline RandyMan

  • Full Member
  • ***
  • Posts: 123
Re: New P-10 CGW GEN II Trigger
« Reply #40 on: December 11, 2018, 08:34:26 AM »
Installing my CGW GenII trigger tonight. I will let you know how it is.


Finally finished this install. Trigger was tight and like other had to polish the trigger bar.
Reset appears to be a little crisper than Gen I trigger.

 

anything