« previous next »
Pages: [1]   Go Down

Author Topic: Primary Machine compensator misalignment  (Read 2216 times)

0 Members and 1 Guest are viewing this topic.

Offline Captain Paul

  • Jr. Member
  • **
  • Posts: 41
Primary Machine compensator misalignment
« on: September 12, 2019, 05:15:39 PM »
Just got my slide back from Primary Machine with the Holosun 507c gr optic install, Omen V2, match barrel, Stealth comp and awesome cerakote job.

I shot a couple hundred rounds and noticed the comp has come out of alignment even though they installed it. So I guess I will remove and clean the threads and reinstall and hopefully have better luck. I'm not sure how much LocTite they put on the set screws and am concerned about stripping them. Can anyone tell me what size hex wrench this takes?
« Last Edit: September 14, 2019, 08:33:30 AM by Wobbly »
Logged

Offline joedirt199

  • Full Member
  • ***
  • Posts: 378
Re: Primary Machine compensator misalignment
« Reply #1 on: September 12, 2019, 05:32:12 PM »
My set screws were not loctited very much and came loose easily. The majority of loctite was on the barrel threads and is holding up nicely. It is a small standard wrench, not metric.
Logged
God created Police so Fireman would have heroes

In God we Trust, everyone else gets searched.

Offline photog22740

  • Full Member
  • ***
  • Posts: 102
Re: Primary Machine compensator misalignment
« Reply #2 on: September 12, 2019, 05:48:07 PM »
Quote from: Captain Paul on September 12, 2019, 05:15:39 PM
Just got my slide back from Primary Machine with the Holosun 507c gr optic install, Omen V2, match barrel, Stealth comp and awesome cerakote job.

I shot a couple hundred rounds and noticed the comp has come out of alignment even though they installed it. So I guess I will remove and clean the threads and reinstall and hopefully have better luck. I'm not sure how much lock tight they put on the set screws and am concerned about stripping them. Can anyone tell me what size hex wrench this takes?

Would love some photos.  Considering this myself.
Logged

Offline Captain Paul

  • Jr. Member
  • **
  • Posts: 41
Re: Primary Machine compensator misalignment
« Reply #3 on: September 12, 2019, 10:57:48 PM »
Quote from: photog22740 on September 12, 2019, 05:48:07 PM
Would love some photos.  Considering this myself.

Sorry, I can't figure how to add pictures. However, they do post pics on their Instagram but not sure if they show any that look as good as mine.

You should do it.

Assuming the comp stays put.
« Last Edit: September 14, 2019, 08:34:42 AM by Wobbly »
Logged

Offline Captain Paul

  • Jr. Member
  • **
  • Posts: 41
Re: Primary Machine compensator misalignment
« Reply #4 on: September 13, 2019, 04:48:46 PM »
Just got an answer in case anyone else needs to know. Metric. .050
Logged

Offline Wobbly

  • Administrator
  • Hero Member
  • *****
  • Posts: 12898
  • Loves the smell of VihtaVuori in the morning !
Re: Primary Machine compensator misalignment
« Reply #5 on: September 14, 2019, 08:39:15 AM »
Logged
In God we trust; On 'Starting Load' we rely.

Offline DOC 1500

  • Hero Member
  • *****
  • Posts: 1940
Re: Primary Machine compensator misalignment
« Reply #6 on: September 14, 2019, 09:00:03 AM »
Why don't you contact raining brass see what he says.
Logged
JOHN 3:16
2 COR.5:17
A Lie is a Lie even if everybody believes it ,
The Truth is the Truth even if nobody believes it !!!

Offline joedirt199

  • Full Member
  • ***
  • Posts: 378
Re: Primary Machine compensator misalignment
« Reply #7 on: September 14, 2019, 01:29:26 PM »
He has kind of ventured away from here after some incidents. I sent him a message awhile back and never got a response.
Logged
God created Police so Fireman would have heroes

In God we Trust, everyone else gets searched.

Offline Captain Paul

  • Jr. Member
  • **
  • Posts: 41
Re: Primary Machine compensator misalignment
« Reply #8 on: September 14, 2019, 06:18:49 PM »
Quote from: DOC 1500 on September 14, 2019, 09:00:03 AM
Why don't you contact raining brass see what he says.

I thought he might answer here. I also emailed them and messaged on Instagram. I wanted to get it done so I could fix it and shoot it this weekend. I ended up just ordering the hex and extra set screws from the websight. Then they answered me on email. That's how I provided the answer here in case anyone else needed it.

It's not a big deal. It's just off a little. I'm still shooting it. I just don't like showing it off with it being crooked.
Logged

Offline DOC 1500

  • Hero Member
  • *****
  • Posts: 1940
Re: Primary Machine compensator misalignment
« Reply #9 on: September 16, 2019, 08:39:15 AM »
Quote from: joedirt199 on September 14, 2019, 01:29:26 PM
He has kind of ventured away from here after some incidents. I sent him a message awhile back and never got a response.
Smart people avoid stupid people, that's why many have gotten off of social media. Myself included.

« Last Edit: September 16, 2019, 08:44:43 AM by DOC 1500 »
Logged
JOHN 3:16
2 COR.5:17
A Lie is a Lie even if everybody believes it ,
The Truth is the Truth even if nobody believes it !!!

Offline Raining_Brass

  • Hero Member
  • *****
  • Posts: 1170
Re: Primary Machine compensator misalignment
« Reply #10 on: September 17, 2019, 10:07:48 AM »
Quote from: Captain Paul on September 13, 2019, 04:48:46 PM
Just got an answer in case anyone else needs to know. Metric. .050
.050" is not metric, it's standard. ;)

At any rate, super sorry for the inconvenience. Shoot me an email if you have any further issues!
Logged

Offline Raining_Brass

  • Hero Member
  • *****
  • Posts: 1170
Re: Primary Machine compensator misalignment
« Reply #11 on: September 17, 2019, 10:10:59 AM »
Quote from: DOC 1500 on September 16, 2019, 08:39:15 AM
Quote from: joedirt199 on September 14, 2019, 01:29:26 PM
He has kind of ventured away from here after some incidents. I sent him a message awhile back and never got a response.
Smart people avoid stupid people, that's why many have gotten off of social media. Myself included.
I wouldn't say stupid people.
I love this forum, but there's just some politics and favoritism going on here that I don't agree with. So unfortunately I have dialed back my posting here quite a bit.
Logged
Pages: [1]   Go Up
« previous next »