Cz P-01 mag base plates

[alouellette]

Been looking for flush fit mag base plates for CZ P-01.  Looking for suggestions. Thanks

[jurek]

I'm not good with nomenclature...
flat metal, plastic or rubber?
I've got all 3 types, but I'm not sure if I get the question correctly....


https://gregcotellc.com/cart/cz-factory-mecgar-actmag-c-173/cz-75b-cz-75-compact-metal-base-plate-m46096-or-cz-0420177012-p-1590.html
https://gregcotellc.com/cart/cz-factory-mecgar-actmag-c-173/cz-75b-cz-85-cz-75-compact-rubber-mag-base-pad-273199000850-p-1420.html

[alouellette]

I guess I could have been more specific. Looking for metal flush fit as the metal is not as prone to clinging to clothing

Thanks I’ll take a look here

[jurek]

These are thin and I've used them for one day. Didn't work so well for concealment.
https://gregcotellc.com/cart/cz-factory-mecgar-actmag-c-173/cz-75b-cz-75-compact-metal-base-plate-m46096-or-cz-0420177012-p-1590.html

These are pretty cool, however 10x more expensive    (check mag compatibility)
http://shookscustoms.com/cz-75-magazine-base-plate-black/

Eventuality I ended up with new Mecgar 15 rounders with plastic base - these work the best for concealed carry.

[Knight3124]

I got two from Greg Cote and didn't like them.  The detent stuck out past the mag base and the lip hit right in the middle of my finger.  I'll just use Mec-Gar 15 round mags.

[SEAKPhotog]

I've got CGW aluminum base plates that I really like.  Not inexpensive however. I also have Armory Craft aluminum base plates which are less expensive but not quite as refined - the rear corners are sharper (but nothing you can't file smooth.

[puddintame]

i have a small pile of these. 8 or so. if you cover shipping. there yours

[Ironhand]

I run the Armory Craft flush aluminum base plates.  They are beautiful, but have some sharp corners that catch on clothing and dig into my car seats when I carry IWB at 0400.  In hindsight, I should have looked for a plastic base to replace the stock rubber plates. 

[puddintame]

i have these on all my cz mags...https://www.berettausa.com/en-us/beretta-92-series-plastic-magazine-bottom-with-steel-insert/c57058/

[jurek]

i have these on all my cz mags...https://www.berettausa.com/en-us/beretta-92-series-plastic-magazine-bottom-with-steel-insert/c57058/

THX !!!!
This is what I was looking for. I've just ordered 3 for my factory mags.
No more rubber ....

Why I haven't found it earlier? There were 3 or 4 posts about Beretta plates on this Forum already... 

[jurek]

i have these on all my cz mags...https://www.berettausa.com/en-us/beretta-92-series-plastic-magazine-bottom-with-steel-insert/c57058/

Update about Beretta plates:

1. They don't fit perfectly...


2. I've had to take some material from the sides and front to fit them into CZ grip shape.


3. After job was done - I could say, they had even better fit than ones from MecGar 15 round magazines.

[BStill]

I have a 2020 P-01 with the new 15-round mags with hard plastic baseplates instead of the soft rubber I had on a previous P-01 with the 14-round mags.  The new plastic baseplates seem fit more flush than the rubber ones did, but the magazine itself seems to extend farther, down just below the lanyard loop.  They must have extended the magazine slightly to get that extra round?

Sent from my LM-G710 using Tapatalk