Author Topic: mods to 97B in Limited10 or 3 gun???  (Read 2943 times)

0 Members and 1 Guest are viewing this topic.

Offline newageroman

  • Hero Member
  • *****
  • Posts: 1108
    • The Brass Bucket - Brass Trading Website
Re: mods to 97B in Limited10 or 3 gun???
« Reply #15 on: December 15, 2022, 04:51:22 AM »
Phase 2 done. fun learning experience. Gutted CZs are the most fun type of puzzle!
A few tips I learned on this round.

  • old lucas oil needle tip did NOT work to lift sear spring leg. It was just a tad too small
  • they make the trigger slave pin a roll pin so that when you get the trigger lined up you can see through the frame and hole and will know when to shove the Floating Trigger Pin
  • trigger is a little better but not super nice just yet
  • more to come
75B-BullShadow SAO (current fav)
SP-01-SAO-compedOpenMajor w/DOT
97E SAO conversion
97B - stock (for now)
SAR copies
..others..

Offline newageroman

  • Hero Member
  • *****
  • Posts: 1108
    • The Brass Bucket - Brass Trading Website
Re: mods to 97B in Limited10 or 3 gun???
« Reply #16 on: December 17, 2022, 08:08:47 PM »
https://rumble.com/v215uug-cz-97b-build-phase-2-sao-conversion.html
The video above ^^^ covers Phase 2 - install of the CGW SAO trigger, lightweight Trigger Return Spring and floating Trigger Pin, removal of the disconnector.

ORDERED - Phase 3 will be - hammer, shelf safety, FPB removal, ext FP

also Lok Grips and locktighted the LCI plate screw.

Hope all have a Merry Christmas!

« Last Edit: December 21, 2022, 11:23:38 AM by newageroman »
75B-BullShadow SAO (current fav)
SP-01-SAO-compedOpenMajor w/DOT
97E SAO conversion
97B - stock (for now)
SAR copies
..others..

Offline newageroman

  • Hero Member
  • *****
  • Posts: 1108
    • The Brass Bucket - Brass Trading Website
Re: mods to 97B in Limited10 or 3 gun???
« Reply #17 on: January 03, 2023, 11:49:52 PM »
All done except test firing and maybe refinishing. and I need to shorten the nub on the other side to sit flat instead of stick out where the left side safety should be.



Does Lok make palmswells for these things?
« Last Edit: January 04, 2023, 03:57:10 AM by Wobbly, Reason: Mods set photo width to 500 »
75B-BullShadow SAO (current fav)
SP-01-SAO-compedOpenMajor w/DOT
97E SAO conversion
97B - stock (for now)
SAR copies
..others..

Offline Earl Keese

  • Hero Member
  • *****
  • Posts: 5069
Re: mods to 97B in Limited10 or 3 gun???
« Reply #18 on: January 04, 2023, 09:17:59 AM »
"Does Lok make palmswells for these things?"
Yep

Offline newageroman

  • Hero Member
  • *****
  • Posts: 1108
    • The Brass Bucket - Brass Trading Website
Re: mods to 97B in Limited10 or 3 gun???
« Reply #19 on: January 04, 2023, 02:47:09 PM »
I thank you and my CreditCard denounces you.
75B-BullShadow SAO (current fav)
SP-01-SAO-compedOpenMajor w/DOT
97E SAO conversion
97B - stock (for now)
SAR copies
..others..

Offline newageroman

  • Hero Member
  • *****
  • Posts: 1108
    • The Brass Bucket - Brass Trading Website
Re: mods to 97B in Limited10 or 3 gun???
« Reply #20 on: January 18, 2023, 05:28:20 PM »
Here is Part2 of the build on Rumble.
https://rumble.com/v2665g4-cz-97b-part-2-cgw-race-hammer-and-wide-shelf-safety-install..html

Part 2:
  • CGW Race Hammer
  • CZC wide shelf safety
  • fitting a sear to a safety vs using the adj sear.

Part 3:
  • Removing FP retaining pin and installing CGW Ext FP retaining pin
  • First shots on the completed build
  • targets and review thoughts
https://rumble.com/v266tu6-cz-97b-part-3-ext.-fp-install-target-results-and-build-review.html
thanks I will be working on getting a 2 cam (close cam) setup for the next build.
« Last Edit: January 18, 2023, 06:30:15 PM by newageroman »
75B-BullShadow SAO (current fav)
SP-01-SAO-compedOpenMajor w/DOT
97E SAO conversion
97B - stock (for now)
SAR copies
..others..

 

anything