Author Topic: "Pin No 9" ?????  (Read 734 times)

0 Members and 1 Guest are viewing this topic.

Offline Towns

  • Hero Member
  • *****
  • Posts: 1746
"Pin No 9" ?????
« on: May 15, 2014, 10:24:25 PM »
I got my decocker sear cage assembled this evening and then proceeded to the hammer, disconnector and strut.

I was preparing to do some hammering, and to my surprise the small pins slid right in without any resistance.  They stay in while assembled but can easily be pushed out. 

So either:

1)  I am the fortunate recipient of new "no hammering necessary" disconnector and strut pins that miraculously will not fall out OR
2)  These are the wrong pins

I ordered them from CZ-USA by clicking on their very handy schematic parts chart.

http://shop.cz-usa.com/czpartslists/cz75BD.pdf

 It is part number 9 that I clicked on which is labelled for all three pins (disconnector, strut and short trigger pin).  When you click on it however, it only is called the "trigger pin short".  I figured since the schematic calls them all part no 9, they're the same.  THis is the link to that page:

http://shop.cz-usa.com/ProductDetail/0420022001_Trigger-Pin-Short-7585-Pin-X2

What gives?

On CZCustom's website, they call the pin "Pin no 9" and says they are for the following purposes:

Pin Number 9
Sometimes called the Three pin.

This pin has three different uses.

Hammer to Strut
Hammer to Dis connector
Trigger to Trigger Bow


Now, I'm wondering if CZ-USA sent me the wrong pins.  They are the perfect length, but the diameter has to be wrong???
“The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.”
― G.K. Chesterton

Offline 441G

  • Full Member
  • ***
  • Posts: 113
Re: "Pin No 9" ?????
« Reply #1 on: May 15, 2014, 11:02:05 PM »
towns - the 9 pin by the trigger will slide in. the 2 #9 pins at the hammer are a press fit

Offline 441G

  • Full Member
  • ***
  • Posts: 113
Re: "Pin No 9" ?????
« Reply #2 on: May 15, 2014, 11:07:22 PM »
towns where are you located? It wouldn't hurt to have someone who has worked on some cz's to see what's going on

Offline ThompsonCustom

  • Hero Member
  • *****
  • Posts: 1076
Re: "Pin No 9" ?????
« Reply #3 on: May 16, 2014, 06:47:04 AM »
Why do you assume they are the wrong part because they slide in and out easy? The factory pins are staked and that's why they do not move. The aftermarket pins that you can buy from CGW also push in and out with next to no force. You could stake the pins or probably just use the smallest amount of red locktite just make sure you don't get any inside the disco or strut hole. I've ran the pins free floating in a cz 75b I use to have for at least a couple thousand rounds and never had any problems.
www.AerospaceArms.com Current Deals:
Faxon 16" Pencil Barrel $148
21% off all magpul products code: "magpul"

Offline Towns

  • Hero Member
  • *****
  • Posts: 1746
Re: "Pin No 9" ?????
« Reply #4 on: May 16, 2014, 09:58:29 AM »
Thanks a bunch guys.  I did go ahead and put them in (figured it wouldn't hurt at least temporarily).  My son actually recommended loctite as well :)
“The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.”
― G.K. Chesterton

Offline Stuart

  • Hero Member
  • *****
  • Posts: 8326
Re: "Pin No 9" ?????
« Reply #5 on: May 16, 2014, 10:09:01 AM »
pins are fine.
I wouldnt use locktite, just personal preference. either leave as is or stake them.
stuart@czcustom.com
czcustom.com

Offline Towns

  • Hero Member
  • *****
  • Posts: 1746
Re: "Pin No 9" ?????
« Reply #6 on: May 16, 2014, 11:12:24 AM »
thanks
“The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.”
― G.K. Chesterton

 

anything