Author Topic: Is the New Evo Carbine Faux Suppressor Removable?  (Read 26121 times)

0 Members and 2 Guests are viewing this topic.

Offline Darbn

  • Newbie
  • *
  • Posts: 14
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #15 on: June 24, 2016, 06:26:16 PM »
So how is the handguard retained on the gun. I am assuming the faux suppressor isn't how its held on?
The handguard on the carbine is kept in place the same way as the pistol handguard.

Offline AZ_CZ

  • Hero Member
  • *****
  • Posts: 2685
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #16 on: June 24, 2016, 06:35:46 PM »
Great info. Thanks to everyone for the feedback and pictures.
CZ Fanbot since 1996

Offline MisterMe

  • Jr. Member
  • **
  • Posts: 49
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #17 on: June 25, 2016, 10:51:49 AM »
Is the faux suppressor a 1/2x28?

Offline AZ_CZ

  • Hero Member
  • *****
  • Posts: 2685
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #18 on: June 25, 2016, 11:37:57 AM »
That's the spec.
CZ Fanbot since 1996

Offline deadduck357

  • Full Member
  • ***
  • Posts: 248
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #19 on: June 25, 2016, 02:17:50 PM »
Will a can index with its muzzle?

Offline jrodicus

  • Jr. Member
  • **
  • Posts: 40
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #20 on: June 25, 2016, 03:42:01 PM »
Will a can index with its muzzle?
No. At least my Evo-9 bottoms out in the carbine's threads. The carbine's threads are not done to suppressor specs. :(. Won't index on the muzzle OR the shoulder. I'm temporarily using a peel washer to make it work. YMMV

Offline AZ_CZ

  • Hero Member
  • *****
  • Posts: 2685
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #21 on: June 25, 2016, 05:48:08 PM »
So what are "suppressor specs"?

I'm looking at the picture here and the picture on the CZC shop 8" barrel and except for the crown they look the same.
CZ Fanbot since 1996

Offline BroncoAZ

  • Jr. Member
  • **
  • Posts: 27
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #22 on: July 24, 2016, 02:00:18 PM »



Notice how A: threads don't go to the shoulder and B: barrel isn't relieved past the threads. Means my suppressor won't thread down far enough to index off the shoulder. AAC says it is fine to index off the face of the muzzle, but I'm concerned that the piston is bottoming out where the threads stop before it can index off anything.

Liberty Suppressors makes a spacer for running a .22 rimfire suppressor on a .223 barrel with long threads, it should work fine for this application as well.

http://libertycans.net/product/22-spacers-for-ars/

I'm sure there are other sources for a 1/2" spacer that would allow the can to shoulder.

Offline GregP74

  • Jr. Member
  • **
  • Posts: 29
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #23 on: November 21, 2016, 07:52:03 PM »
Sorry for replying to an old thread but this seemed like the place to go.

I've got the carbine with the muzzle brake. Someone from one of the CZ boards sent me is faux suppressor and I'm going to put it on, but first I need to get the muzzle brake off. Anything special I need to do to get it off?

Offline rvt

  • Newbie
  • *
  • Posts: 1
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #24 on: November 22, 2016, 10:54:13 AM »
Cz-USA told me the muzzle break just unscrews.

Offline mursalot

  • Sr. Member
  • ****
  • Posts: 298
  • FULL AUTO
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #25 on: November 22, 2016, 12:11:18 PM »
Heat it up first. It might have thread locker on it just like the pistol barrel nut
2 things you never want to hear when you pull the trigger:

"click" when you expect it to go "bang" and

"bang" when you expect it to go "click"

Offline GregP74

  • Jr. Member
  • **
  • Posts: 29
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #26 on: November 23, 2016, 01:33:20 PM »
I put a wrench over the hex part of the muzzle break. It was kinda hard to turn at first but it broke free pretty quick. Didn't seem to have much if anything holding it on.

When I put the faux suppressor on I used some blue loctite, as I've read that's what's done from the factory.

Offline Grendel

  • Administrator
  • Hero Member
  • *****
  • Posts: 7114
  • 'Live long, and Prosper'
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #27 on: November 23, 2016, 07:18:28 PM »
This is not a WTB/WTS thread. Knock it off.
Corruptissima re publica plurimae leges - Tacitus

Inter arma enim silent leges - Cicero

I wasn't born in America, but I got here as fast as I could.

Offline scootle

  • Newbie
  • *
  • Posts: 11
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #28 on: November 23, 2016, 08:48:19 PM »
This is not a WTB/WTS thread. Knock it off.

Ah, my bad... shoulda looked for the right forum for that.  Just wasn't thinking when I saw that other post I quoted.  Will post appropriately in the right place later.

My faux suppressor was removable by hand... the torque spec didn't seem that high and/or they didn't use thread locker.

For folks putting on muzzle devices, are you using crush washers to clock them?  The faux suppressor just has a washer in there which somehow seems to clock the SilencerCo logo reasonably well.  Depending how the laws in CA play out, I might have to go with a brake to get the OAL to snuff next year to explore unpinning the folding stock.

Offline aspenmeadow

  • Newbie
  • *
  • Posts: 6
Re: Is the New Evo Carbine Faux Suppressor Removable?
« Reply #29 on: February 24, 2017, 03:16:14 PM »
I have the EVO carbine with the faux suppressor, and was hoping that someone would give me a clue on the removal of it. I want to mount a M-LOC flashlight/laser on the forearm, but can't get the nuts past the faux can. I was able to unscrew the can with the use a strap wrench, but the terminal piece remained on the barrel (it looks like the business end of a real compressor). I can't get enough torque because the edge is only about an 1/8 inch wide. I would prefer to take the forearm off but can't see how to do that. (The manual is useless and their web site gives nothing) any ideas?

 

anything