« previous next »
Pages: [1]   Go Down

Author Topic: Changing P07 back strap pointers  (Read 1787 times)

0 Members and 1 Guest are viewing this topic.

Offline Lexman1970

  • Jr. Member
  • **
  • Posts: 35
Changing P07 back strap pointers
« on: July 15, 2016, 11:30:58 PM »
I have the flush fitting hammer spring plug and when I bought my Gen 2 P07 it had the small strap installed so I changed it out for the medium and it was all I could do to get that bleep plug in and replace. Well I've been pondering the large module wondering if it will give me a more true say P01 feel, but I don't have fond memories of going through that he'll again. Does anyone have a fix for doing this other than pure brute finger strength??
Logged

Offline viking499

  • Hero Member
  • *****
  • Posts: 4437
Re: Changing P07 back strap pointers
« Reply #1 on: July 16, 2016, 12:39:25 AM »
I always use the table or something solid to push against.  Once the mainspring plug is in, i install the pin.  If everything does not line up, I ease off on the pressure, realign, and go again.
Logged

Offline Winkel

  • Sr. Member
  • ****
  • Posts: 901
Re: Changing P07 back strap pointers
« Reply #2 on: July 16, 2016, 12:40:52 AM »
On my bench in my basement, the frame is made of 2x4 lumber.  I have a round head sheet metal screw screwed into the face of the frame.  With the frame of the gun pointing down, I press the hammer spring plug against the head of the screw while pushing the pin out with a small punch. 

It allows pretty good leverage and works well for me.
Logged

Offline s0nspark

  • Administrator
  • Hero Member
  • *****
  • Posts: 2043
  • System Admin
Re: Changing P07 back strap pointers
« Reply #3 on: July 16, 2016, 06:47:41 AM »
Quote from: Winkel on July 16, 2016, 12:40:52 AM
On my bench in my basement, the frame is made of 2x4 lumber.  I have a round head sheet metal screw screwed into the face of the frame.  With the frame of the gun pointing down, I press the hammer spring plug against the head of the screw while pushing the pin out with a small punch. 

It allows pretty good leverage and works well for me.

I rigged up something similar with a nylon-tipped punch and my vise.

I never thought I'd miss the lanyard loop LOL
Logged
"A man's character is his fate."

Offline Lexman1970

  • Jr. Member
  • **
  • Posts: 35
Re: Changing P07 back strap pointers
« Reply #4 on: July 16, 2016, 12:07:26 PM »
There we go now I can make any of these suggestions happen. Thank you to all!!
Logged

Offline M1A4ME

  • Hero Member
  • *****
  • Posts: 7578
  • I've shot the rest, I now own the best - CZ
Re: Changing P07 back strap pointers
« Reply #5 on: July 17, 2016, 06:34:11 PM »
Quote from: Winkel on July 16, 2016, 12:40:52 AM
On my bench in my basement, the frame is made of 2x4 lumber.  I have a round head sheet metal screw screwed into the face of the frame.  With the frame of the gun pointing down, I press the hammer spring plug against the head of the screw while pushing the pin out with a small punch. 

It allows pretty good leverage and works well for me.

I was fighting with my CZ 85 Friday morning trying to get the plug out and back in again.  I got the drill out with a phillips head bit in it and ran a round headed screw (almost) into the door frame stud by my bench.  Made it very easy to get that plug pushed back in so the pin would slide in easy.  I don't have enough hands (only 2) to get it done any other way.
Logged
I just keep wasting time and money on other brands trying to find/make one shoot like my P07 and P09.  What is wrong with me?

Offline Winkel

  • Sr. Member
  • ****
  • Posts: 901
Re: Changing P07 back strap pointers
« Reply #6 on: July 19, 2016, 09:15:09 PM »
Excellent!  Glad I could share a little tip!
Logged
Pages: [1]   Go Up
« previous next »