Author Topic: P-10c issue with slide lock spring!  (Read 3449 times)

0 Members and 1 Guest are viewing this topic.

Offline jlopeznew

  • Newbie
  • *
  • Posts: 2
P-10c issue with slide lock spring!
« on: August 20, 2017, 03:16:14 PM »
Hello everyone! Im new to the forum. Today I went to the range with my CZ P10c, my first handgun ever (I'm really enjoying it). When came home try to take apart to clean it (around 1000 rounds) and as you can see in the picture, the slide got stock, after checking it I found out the slide lock spring was out of place. I forced a little and the slide came out. I tried to put the spring back in place but it keep coming out. I don't know what to do. Any suggestions?
Thanks.

Sent from my Pixel using Tapatalk


Offline oldfrank

  • Sr. Member
  • ****
  • Posts: 870
Re: P-10c issue with slide lock spring!
« Reply #1 on: August 20, 2017, 03:52:28 PM »
<iframe width="560" height="315" src="https://www.youtube.com/embed/eUdPCtK1Zxo" frameborder="0" allowfullscreen></iframe>

This  video will show complete disassembly of your gun. I don't know how the spring could come out from under the pin without breaking but take it apart and see if the spring is ok.

Offline Bossgobbler

  • Sr. Member
  • ****
  • Posts: 890
Re: P-10c issue with slide lock spring!
« Reply #2 on: August 20, 2017, 06:31:35 PM »
call CZ-USA call 1-800-955-4486 or e-mail warranty@cz-usa.com

Offline jlopeznew

  • Newbie
  • *
  • Posts: 2
Re: P-10c issue with slide lock spring!
« Reply #3 on: August 20, 2017, 06:50:29 PM »
Thanks guys. I will be contacting CZ tomorrow to see how this will end up. Im new to guns, so I don't have tools to disassemble. Hopefully everything will be fine. Btw Im always reading in the forum. Got to shoot a p07 today too. Feels good on the hands. Before I rented the p09 in my local range. Did not like it. Im thinking on getting the PCR later, but want to try it first. I shoot Berettas, p320s, vp9s, glocks and arcus. Nothing feels better than Czs. Im starting to think Czs are addictive!

Sent from my Pixel using Tapatalk


Offline Jigo23

  • Full Member
  • ***
  • Posts: 397
Re: P-10c issue with slide lock spring!
« Reply #4 on: August 20, 2017, 08:54:37 PM »
You only need a small punch, doesn't really take tools to disassemble. Sounds to me like someone had disassembled it and when reassembling didn't make sure the pin was going through the hole in the slide stop assembly. Pretty easy to do if you aren't paying attention when reassembling. Check out videos for disassembly and reassembly really not hard at all and will help you learn how the gun works too. Btw, you will love the PCR, get it! :)

Offline Craig M Arnold

  • Full Member
  • ***
  • Posts: 413
Re: P-10c issue with slide lock spring!
« Reply #5 on: August 20, 2017, 11:14:10 PM »
I second getting the PCR. I have carried one everyday for 10 years or more. I can not say enough good things about it.

Best regards. 
Make America Great Again

Offline SI VIS PACEM PARRABELLUM

  • Hero Member
  • *****
  • Posts: 5837
Re: P-10c issue with slide lock spring!
« Reply #6 on: August 21, 2017, 05:04:15 AM »
I second getting the PCR. I have carried one everyday for 10 years or more. I can not say enough good things about it.

Best regards.

Agree.Been carrying my PCR for 9 years and nothing else compares or even comes close as a possible replacement. Possibly the perfect all around handgun.