P-10c range report.....mixed results

[wyoung]

Mine did the same thing when I first started shooting it. It only hung up once but I don't have a large number of rounds through mine. It has the fully chamfered slide plate from the factory.  I sent it back to CZ for the plate issue and the striker issue. They only replaced the striker and said they shot it and it was fine. The rear plate is still loose and the new striker still rotates.

I spoke to the guy who worked on my pistol before they shipped it back and he basically admitted the issue is they can't get any of the newer parts to upgrade the older guns because the newer parts are dedicated to new production.

My guess is the half circle area on the back of your striker assembly wasn't properly snapped into place on the rear plate which will allow excessive movement of both the striker assembly and plate.

Not to sound naive but what does chamfered mean?

What was your striker issue?

Striker rotates?  My firing pin does have a little play in it




Sent from my iPhone using Tapatalk

Older P-10 didn't have the angled or chamfered slide plate so I was confused when my slide hung up. I had read where the angle on the plate was supposed to stop it from happening.

Yes, the striker issue is the rotation. When the striker isn't cocked, everything feels solid and it won't rotate. If I cock the striker and lock the slide back, the striker will rotate and snap/lock into place.

[2tango2]

Are we talking about what is circled in red or green?




Sent from my iPhone using Tapatalk

[wyoung]

Are we talking about what is circled in red or green?




Sent from my iPhone using Tapatalk

That would be the green circle which is the striker sear. If mine is in the state in this picture, everything feels solid and won't move very much because the striker isn't under spring tension.

Then I can take my thumb and pull the striker back (left in the picture) until the striker block safety circled in red clicks into place. Then with everything under tension, things move around a lot more back there. The striker assembly will shift and the back plate will move more when I press the striker sear in different directions.

At this time, if I press the striker sear what would be down in the picture, the striker will rotate about 1/8 turn and will snap into place.

[2tango2]

Ok gotcha

Mine doesn?t really make an audible click like be seen in You Tube videos.   It just sort of falls in place.  When in that state it will wiggle a bit but not rotate as you describe


Is it supposed to be rock solid with no movement in either position?


Sent from my iPhone using Tapatalk

[wyoung]

Ok gotcha

Mine doesn?t really make an audible click like be seen in You Tube videos.   It just sort of falls in place.  When in that state it will wiggle a bit but not rotate as you describe


Is it supposed to be rock solid with no movement in either position?


Sent from my iPhone using Tapatalk

I think as long as you can't make it hang on the back of the slide like mine does you'll be fine.





Out of all the other brand striker fired guns I've handled, they are all rock as far as excessive movement of the striker.

I've read the Cajun Gun Works tool steel striker helps and there's a thread where they say they're supposed to be working on a fix for excessive movement back there.

[2tango2]

Oh snap!   Yeah I can?t get it to do that (as far as I know) or should I say it hasn?t done that yet.......yet

I have an email in to CZ, waiting to hear back


Sent from my iPhone using Tapatalk

[2tango2]

Oh snap!   Yeah I can?t get it to do that (as far as I know) or should I say it hasn?t done that yet.......yet

I have an email in to CZ, waiting to hear back


Sent from my iPhone using Tapatalk

Still waiting.......


Sent from my iPhone using Tapatalk

[armoredman]

1-800-955-4486. That amount of play was really excessive and needs to be addressed.

[Crossfaced]

Im very disappointed to read about the issues with the P10c. I was at my club the other day and tried another members P10c. I loved how it shot. Though it was a bit gritty I loved the trigger and it fits me well.

I was going to get one to try as my EDC but I can?t trust this gun now.

[cntrydawwwg]

Just curious why you feel you can?t trust it. Sure, there?s been some posts about issues. Even when you take the entire internet into account, there still isn?t that many issues IMO. People cross post about issues, sometimes they even use different user names.

 If you take 1 person with an issue, and they post on 7 different forums, under 7 different usernames, that makes it look like 7 issues, when in reality it?s only 1. Not being a fanboy at all. Just saying compared to the 1000?s upon 1000?s P10c?s sold, the good far outweighs the bad. And CZ CS is taking care of any issues that may pop up. JMHO

[Crossfaced]

Just curious why you feel you can?t trust it. Sure, there?s been some posts about issues. Even when you take the entire internet into account, there still isn?t that many issues IMO. People cross post about issues, sometimes they even use different user names.

 If you take 1 person with an issue, and they post on 7 different forums, under 7 different usernames, that makes it look like 7 issues, when in reality it?s only 1. Not being a fanboy at all. Just saying compared to the 1000?s upon 1000?s P10c?s sold, the good far outweighs the bad. And CZ CS is taking care of any issues that may pop up. JMHO

I hear ya, and actually agree with what your saying for the most part. However I have a hard time placing all my trust in a relatively new platform when it has issues, which most do. I know this will be a fine weapon. I will own one but will probably wait for V2.

[cntrydawwwg]

Understand what you?re sayin[emoji6]

[2tango2]

I?m going to hit the range this week and put another 100 downrange and see if I can induce the issue.

Live fire may trigger it more than me trying to make it happen while dry firing.


Sent from my iPhone using Tapatalk

[highxj]

2tango2, mine did the exact same thing, on round # six of its' maiden voyage.  I wasn't impressed.  New style back plate as well.  I've shot maybe a hundred rounds without a repeat.  But the sloppy fit of everything back there gives me pause.  Like you I was unable to manually duplicate this condition and am a bit stumped as to how it happened.  The engagement of the striker sleeve to the plate is quite shallow.

I won't be carrying this gun until I hear of a bulletproof fix for this issue.  I'll be checking in here of often.

[armoredman]

Understandable indeed. I am actually looking to get a new one to compare to my original FDE which has had zero issues so far. It is my EDC right now. But I understand anyone's hesitation to be a beta tester.