The Original CZ Forum
CZ PISTOL CLUBS => CZ Polymer Pistols: P10, P-07, P-09 => Topic started by: fastlane604 on February 03, 2018, 06:51:11 PM
-
I picked up my new P-10 C today. Just returned from the range. Shoots accurately. Grip texture is aggressive. I admit, my hand toughness isn't what it once was, but my hands still feel warm. Mag release is too flat and obstinate, but I am used to extended releases on Shadows. I know CGW has a fix coming, if not already.
Trigger is very smooth with an amazingly short reset. Mine measured about 5.25 lb on my gauge which was more than I expected. I will shoot it awhile and check it again. However, I was probably always going to swap it out for the new CGW trigger. I want to get rid of most of the pre-travel.
I am going to change out the sights. I have fiber optic fronts and serrated blades on my Shadows. However, my PC Shield has the red fiber optic front and the green fiber optic rear and I like those and seem to shoot them well. I am leaning that direction if I can find some to fit. Have any of you put them on your PC-10 C?
-
Just saw the fiber optic pair on CGW site.
-
I have the CZC HTAC rear/FO front combo on mine. I like the CGW EZ/D's on my 75 and these are pretty close.
-
I picked up my new P-10 C today. Just returned from the range. Shoots accurately. Grip texture is aggressive. I admit, my hand toughness isn't what it once was, but my hands still feel warm. Mag release is too flat and obstinate, but I am used to extended releases on Shadows. I know CGW has a fix coming, if not already.
Trigger is very smooth with an amazingly short reset. Mine measured about 5.25 lb on my gauge which was more than I expected. I will shoot it awhile and check it again. However, I was probably always going to swap it out for the new CGW trigger. I want to get rid of most of the pre-travel.
I am going to change out the sights. I have fiber optic fronts and serrated blades on my Shadows. However, my PC Shield has the red fiber optic front and the green fiber optic rear and I like those and seem to shoot them well. I am leaning that direction if I can find some to fit. Have any of you put them on your PC-10 C?
My stock P-10 also had a trigger pull of 5 pounds 4 ounces which was higher than I expected. I have since installed an HBI flat trigger with a 3 pound striker spring and a CGW tool steel striker and the average pull on my Lyman digital scale is 3 pounds 14 ounces. I also polished the trigger components. All of this has made my P-10 an absolute pleasure to shoot. Good luck with yours.
-
I picked up my new P-10 C today. Just returned from the range. Shoots accurately. Grip texture is aggressive. I admit, my hand toughness isn't what it once was, but my hands still feel warm. Mag release is too flat and obstinate, but I am used to extended releases on Shadows. I know CGW has a fix coming, if not already.
Trigger is very smooth with an amazingly short reset. Mine measured about 5.25 lb on my gauge which was more than I expected. I will shoot it awhile and check it again. However, I was probably always going to swap it out for the new CGW trigger. I want to get rid of most of the pre-travel.
I am going to change out the sights. I have fiber optic fronts and serrated blades on my Shadows. However, my PC Shield has the red fiber optic front and the green fiber optic rear and I like those and seem to shoot them well. I am leaning that direction if I can find some to fit. Have any of you put them on your PC-10 C?
My stock P-10 also had a trigger pull of 5 pounds 4 ounces which was higher than I expected. I have since installed an HBI flat trigger with a 3 pound striker spring and a CGW tool steel striker and the average pull on my Lyman digital scale is 3 pounds 14 ounces. I also polished the trigger components. All of this has made my P-10 an absolute pleasure to shoot. Good luck with yours.
How much of the pre-travel does the HBI flat trigger eliminate?
-
I picked up my new P-10 C today. Just returned from the range. Shoots accurately. Grip texture is aggressive. I admit, my hand toughness isn't what it once was, but my hands still feel warm. Mag release is too flat and obstinate, but I am used to extended releases on Shadows. I know CGW has a fix coming, if not already.
Trigger is very smooth with an amazingly short reset. Mine measured about 5.25 lb on my gauge which was more than I expected. I will shoot it awhile and check it again. However, I was probably always going to swap it out for the new CGW trigger. I want to get rid of most of the pre-travel.
I am going to change out the sights. I have fiber optic fronts and serrated blades on my Shadows. However, my PC Shield has the red fiber optic front and the green fiber optic rear and I like those and seem to shoot them well. I am leaning that direction if I can find some to fit. Have any of you put them on your PC-10 C?
My stock P-10 also had a trigger pull of 5 pounds 4 ounces which was higher than I expected. I have since installed an HBI flat trigger with a 3 pound striker spring and a CGW tool steel striker and the average pull on my Lyman digital scale is 3 pounds 14 ounces. I also polished the trigger components. All of this has made my P-10 an absolute pleasure to shoot. Good luck with yours.
How much of the pre-travel does the HBI flat trigger eliminate?
I have no way of measuring the reduction in pre-travel but I would guess somewhere around 25%. Again that's just a guess.
-
Just saw the fiber optic pair on CGW site.
That?s what I did. I have the Dawson FO sights on the majority of my pistols.
-
I picked up my new P-10 C today. Just returned from the range. Shoots accurately. Grip texture is aggressive. I admit, my hand toughness isn't what it once was, but my hands still feel warm. Mag release is too flat and obstinate, but I am used to extended releases on Shadows. I know CGW has a fix coming, if not already.
Trigger is very smooth with an amazingly short reset. Mine measured about 5.25 lb on my gauge which was more than I expected. I will shoot it awhile and check it again. However, I was probably always going to swap it out for the new CGW trigger. I want to get rid of most of the pre-travel.
I am going to change out the sights. I have fiber optic fronts and serrated blades on my Shadows. However, my PC Shield has the red fiber optic front and the green fiber optic rear and I like those and seem to shoot them well. I am leaning that direction if I can find some to fit. Have any of you put them on your PC-10 C?
My stock P-10 also had a trigger pull of 5 pounds 4 ounces which was higher than I expected. I have since installed an HBI flat trigger with a 3 pound striker spring and a CGW tool steel striker and the average pull on my Lyman digital scale is 3 pounds 14 ounces. I also polished the trigger components. All of this has made my P-10 an absolute pleasure to shoot. Good luck with yours.
How much of the pre-travel does the HBI flat trigger eliminate?
I have no way of measuring the reduction in pre-travel but I would guess somewhere around 25%. Again that's just a guess.
Thank you.
-
Be curious to know if anyone has actually measured the reduction in take up between the stock P-10 trigger and the HB Industries flat trigger.