Author Topic: Garbage Accuracy From CZ 750  (Read 398 times)

0 Members and 1 Guest are viewing this topic.

Offline hoop223556

  • Newbie
  • *
  • Posts: 5
Garbage Accuracy From CZ 750
« on: December 30, 2018, 08:54:28 PM »
I bought a CZ 750 awhile back and have had nothing but problems with it accuracy wise. Always goes bang and the mags usually feed but the best it'll shoot is 2MOA with a lot of fliers than can be 3-5MOA. Action screws don't stay tight no matter what, they always shoot loose and there's no bedding or pillars just a blob of epoxy around the front recoil lug. Also when the action screws are tight sometimes the front of the stock warps and rubs against the barrel when in direct sunlight so that screws accuracy too.

Any thoughts? I'm about ready to throw it in a lake.

Offline DWARREN

  • Sr. Member
  • ****
  • Posts: 553
  • Grumpy Old Guy
Re: Garbage Accuracy From CZ 750
« Reply #1 on: December 30, 2018, 09:53:51 PM »
Call CZ about the problems.
SHUT UP AND RELOAD!

Offline hoop223556

  • Newbie
  • *
  • Posts: 5
Re: Garbage Accuracy From CZ 750
« Reply #2 on: February 09, 2019, 12:47:31 AM »
I got frustrated and took it to a local gunsmith who did a pillar/glass bedding job which is how the rifle should have come from the factory. Next step will be a couple flush cups for sling.

By the time CZ returned my call the rifle was already at my gunsmith. I'm a fan of their rifles and pistols but their warrant service doesn't seem to be that good to put it mildly.

Offline Rock-it3

  • Full Member
  • ***
  • Posts: 495
Re: Garbage Accuracy From CZ 750
« Reply #3 on: February 09, 2019, 10:29:14 AM »
Did you contact CZ prior to taking it to your gunsmith? Your post isn't quite clear.

Offline hoop223556

  • Newbie
  • *
  • Posts: 5
Re: Garbage Accuracy From CZ 750
« Reply #4 on: February 09, 2019, 11:27:34 AM »
Yes called and emailed, like I said they did respond but it took a couple weeks and by then it was at my gunsmith's.

Offline painter

  • Hero Member
  • *****
  • Posts: 5793
Re: Garbage Accuracy From CZ 750
« Reply #5 on: February 09, 2019, 11:50:31 AM »
When you called, was it during normal business hours, or did you leave a message?

The reason I ask, is CZ has typically been excellent once you actually get someone on the phone. They've never been stellar about email.
I had the right to remain silent...

but not the ability.

Offline hoop223556

  • Newbie
  • *
  • Posts: 5
Re: Garbage Accuracy From CZ 750
« Reply #6 on: February 09, 2019, 12:49:34 PM »
Yeah I called during normal business hours I probably called a few times after I made that first post. The message I got was that if it was within 5 years and I had the original receipt and paperwork it would be under warranty otherwise I would have to pay their gunsmith and he had a 60-90 day wait.

That was why I wound up taking it to a local guy. He was all excited because he likes mausers so he did a trigger job on it too.

Offline coolbox

  • Hero Member
  • *****
  • Posts: 1981
Re: Garbage Accuracy From CZ 750
« Reply #7 on: February 12, 2019, 03:54:03 AM »
Sorry for your experience.
I have seen two CZ750 rifles, with fellow shooters. Both shoot sub MOA in general with decent 175smk based factory ammunition, and sub half MOA with hand loads. They do not have the action screw coming loose issue. One of them was glass bedded at some stage.

I hope yours comes back to your liking.
Life is too short to waste on a bad trigger pull

 

anything