« previous next »
Pages: [1]   Go Down

Author Topic: P01 Omega trigger bar spring tweak  (Read 1449 times)

0 Members and 1 Guest are viewing this topic.

Offline Jeep_Nut

  • Full Member
  • ***
  • Posts: 199
P01 Omega trigger bar spring tweak
« on: April 24, 2020, 02:00:47 PM »
I know on the P07, the trigger bar spring tension can be reduced by bending it slightly downward resulting in a lighter, smooter DA pull. Can the same be done to the PO1 Omega since it's basically the same setup?
Logged

Offline briang2ad

  • Hero Member
  • *****
  • Posts: 3276
Re: P01 Omega trigger bar spring tweak
« Reply #1 on: April 25, 2020, 11:12:00 AM »
Yes - but the impact may be minimal.  If your action is already smooth and without much stacking you will notice a difference.  If is is FULL of stacking - nothing but a ton of work is going to change that.
Logged

Offline jurek

  • Hero Member
  • *****
  • Posts: 1555
  • NRA Pistol Instructor, RSO
Re: P01 Omega trigger bar spring tweak
« Reply #2 on: April 25, 2020, 12:51:33 PM »
briang2ad gets a few good posts about Omega trigger. I recommend to search and read.

In my case, smooth DA pull at P-01 Omega came after lowering weight of hammer spring, changing DA roller and using Reduced Power Trigger Return Spring.
And of course - smoothing and polishing components is a must.
Logged

Offline Jeep_Nut

  • Full Member
  • ***
  • Posts: 199
Re: P01 Omega trigger bar spring tweak
« Reply #3 on: April 25, 2020, 07:55:27 PM »
Either i got a good one or I’m just not as picky as you guys. The DA in mine is pretty good stock. I do have CGW springs on the way though. Might as well make it even better.


Sent from my iPhone using Tapatalk
Logged

Offline jurek

  • Hero Member
  • *****
  • Posts: 1555
  • NRA Pistol Instructor, RSO
Re: P01 Omega trigger bar spring tweak
« Reply #4 on: April 25, 2020, 11:42:22 PM »
Quote from: bleepYankee on April 25, 2020, 07:55:27 PM
Either i got a good one or I’m just not as picky as you guys. The DA in mine is pretty good stock. I do have CGW springs on the way though. Might as well make it even better.
Sent from my iPhone using Tapatalk
Yeah, P-01 Omega is not bad out of the box... but whoever enjoyed 1911 before, would be always looking for better trigger.
My very first handgun was PPQ and none of my CZs with CGW parts have trigger close to Walther's.  :'(
Logged

Offline briang2ad

  • Hero Member
  • *****
  • Posts: 3276
Re: P01 Omega trigger bar spring tweak
« Reply #5 on: April 26, 2020, 04:13:07 PM »
The point is that the Omega is all over the map.  You CAN land one OTB and it might be smooth and consistent, or you can get one that NO normal amount of polishing will help at all.  Then you have to mod parts.
Logged

Offline Tok36

  • Hero Member
  • *****
  • Posts: 6243
Re: P01 Omega trigger bar spring tweak
« Reply #6 on: April 26, 2020, 06:04:14 PM »
   My P-09s DA felt like one of those heavy duty silver staplers when i got it. Stack, stack, stack, stack, Clank! After installing all of the CGW parts, polishing and some break in, it is getting there. Now it feels like a nice office stapler.  ;D
Logged
Will work for CZ pics! (including but not limited to all CZ clones)

Offline jurek

  • Hero Member
  • *****
  • Posts: 1555
  • NRA Pistol Instructor, RSO
Re: P01 Omega trigger bar spring tweak
« Reply #7 on: April 26, 2020, 08:10:37 PM »
Quote from: Tok36 on April 26, 2020, 06:04:14 PM
After installing all of the CGW parts, polishing and some break in, it is getting there. Now it feels like a nice office stapler.  ;D

And now you have nice Cajunized stapler gun  ;)

sorry, just kidding  ;D :P ::)
Logged
Pages: [1]   Go Up
« previous next »