Author Topic: P10C Replacement striker parts  (Read 696 times)

0 Members and 1 Guest are viewing this topic.

Offline mwawrzyniec

  • Newbie
  • *
  • Posts: 13
P10C Replacement striker parts
« on: October 12, 2020, 12:53:25 PM »
Where is the best place to buy a firing pin assembly or its individual parts?  I need the 2 plastic spring holders.
« Last Edit: October 12, 2020, 03:47:52 PM by Wobbly, Reason: Mods clarified request »

Offline viking499

  • Hero Member
  • *****
  • Posts: 4390
Re: Replacement parts
« Reply #1 on: October 12, 2020, 02:06:33 PM »
For which gun?

Offline mwawrzyniec

  • Newbie
  • *
  • Posts: 13
Re: Replacement parts
« Reply #2 on: October 12, 2020, 02:49:25 PM »
Sorry the P10-C

Offline Claymore504

  • Sr. Member
  • ****
  • Posts: 598
Re: P10-C Replacement parts
« Reply #3 on: October 12, 2020, 02:52:09 PM »
Welcome to the forum. Try calling CZ directly, The webstore is down right now.

Offline mwawrzyniec

  • Newbie
  • *
  • Posts: 13
Re: P10C Replacement striker parts
« Reply #4 on: October 12, 2020, 05:01:10 PM »
Thank you.  I'll give that a try when they re open tomorrow.   

Offline Type5

  • Full Member
  • ***
  • Posts: 177
Re: P10C Replacement striker parts
« Reply #5 on: October 12, 2020, 05:23:06 PM »
I just ordered by phone half a dozen items for a P-10 S OR.
Among the items I wanted was a firing pin and main spring  - they said I could order them it would be about $45 USD or for about and additional $10 USD I could get the whole firing pin assembly. I went that way - It includes the two clips you mention - shipping is a flat $9 via Fed-EX.
I just mention it because it you intend to have some spare parts on hand buying the assembly might be over all cheaper.

Offline mwawrzyniec

  • Newbie
  • *
  • Posts: 13
Re: P10C Replacement striker parts
« Reply #6 on: October 12, 2020, 07:18:26 PM »
Do these cups wear out frequently or is this just bad luck


Offline rgunner1

  • Jr. Member
  • **
  • Posts: 27
  • Stay Upright...
Re: P10C Replacement striker parts
« Reply #7 on: October 12, 2020, 09:59:29 PM »
Wear out ? can you expand ?
Stay Upright
    DVC

Offline mwawrzyniec

  • Newbie
  • *
  • Posts: 13
Re: P10C Replacement striker parts
« Reply #8 on: October 13, 2020, 09:12:57 AM »
The cups wont stay seated. The striker spring is pushing them out towards the end of the striker.

https://imgur.com/a/pTCUa5A
« Last Edit: October 14, 2020, 06:38:48 AM by Wobbly »

Offline anach

  • Jr. Member
  • **
  • Posts: 45
Re: P10C Replacement striker parts
« Reply #9 on: October 13, 2020, 04:47:36 PM »
Glock striker cups are also reported to work perfectly, just in case you can find those local/have some lying around.

Offline mwawrzyniec

  • Newbie
  • *
  • Posts: 13
Re: P10C Replacement striker parts
« Reply #10 on: October 13, 2020, 05:59:25 PM »
Glock striker cups are also reported to work perfectly, just in case you can find those local/have some lying around.
Thanks, I read that somewhere else on the forum.  I ended up ordering them, so i'll let you know if they work.  Am I unlucky or is this a commonly worn out part?

Offline Duke Nukem

  • Full Member
  • ***
  • Posts: 167
Re: P10C Replacement striker parts
« Reply #11 on: October 14, 2020, 10:02:54 AM »
Am I unlucky or is this a commonly worn out part?

Is it possible to install them incorrectly?  Could they go in upside down?

Offline anach

  • Jr. Member
  • **
  • Posts: 45
Re: P10C Replacement striker parts
« Reply #12 on: October 14, 2020, 10:16:19 AM »
I think it's a cheaply made-high wear part that can be easily be damaged during assembly.  ¯\_(?)_/¯

You could try swapping the direction of the spring in case the spring diameter is wonky?

Offline Mjolnir

  • Full Member
  • ***
  • Posts: 255
Re: P10C Replacement striker parts
« Reply #13 on: November 14, 2020, 05:13:41 PM »
Will Glock STRIKER SPRINGS also work?

If so, what affect does it have on trigger pull?


Sent from my iPhone using Tapatalk

Offline rgunner1

  • Jr. Member
  • **
  • Posts: 27
  • Stay Upright...
Re: P10C Replacement striker parts
« Reply #14 on: November 16, 2020, 07:13:49 PM »
Glock cups works I know as I have them in one of my P10'S ; Yes glock striker springs work too as I have tried them as well but now just run the Theta trigger and -15% striker spring in both my set ups. And yes those cup's in the photo look like toast...
Stay Upright
    DVC

 

anything