« previous next »
Pages: [1]   Go Down

Author Topic: Help with CGW Disconnect  (Read 1628 times)

0 Members and 2 Guests are viewing this topic.

Offline oldfrank

  • Sr. Member
  • ****
  • Posts: 870
Help with CGW Disconnect
« on: October 20, 2013, 01:21:47 PM »
I installed the drop in CGW disconnect on my CZ 85. Everything seems to work fine unless I hold the trigger back,cycle the slide and attempt to pull the trigger again.

I have to rock the hammer back ever so slightly and the trigger will then work normally. I want to be able to fire from reset if I am going to try to shoot this in a match.

Can anyone shed some light on this?  I plan on calling the shop tomorrow but if this is a common problem with a quick fix I would like to fix it today and go to the range tomorrow.

Thanks!

Logged

Offline oldfrank

  • Sr. Member
  • ****
  • Posts: 870
Re: Help with CGW Disconnect
« Reply #1 on: October 20, 2013, 01:41:52 PM »
UH Oh :( I think I falsely blamed the disconnect and it is not the disco.

I also replaced the safety with a brand new one and I checked all the safety functions and they all worked, I did not check to see if the trigger would reset after being held back as I did not see the safety affecting this but apparently it does.
Logged

Offline oldfrank

  • Sr. Member
  • ****
  • Posts: 870
Re: Help with CGW Disconnect
« Reply #2 on: October 20, 2013, 03:30:47 PM »
Dang, if I keep talking to myself and studying the gun I think I got it fixed. :)

I swapped safeties two or three times and sometimes one worked and sometimes it didn't and vice versa. The problem starting coming and going until I noticed the trigger pivot pin was sticking out about 1/8". :o

I pushed it back in and so far everything works fine with either safety installed.

I am going to the range tomorrow, that will be the true test.
Logged

Offline 1SOW

  • Hero Member
  • *****
  • Posts: 15006
  • GO GREEN - Recycle 9MM
Re: Help with CGW Disconnect
« Reply #3 on: October 20, 2013, 05:16:00 PM »
I know the 'feeling'.
What trigger pin are you using?  Stock? CGW solid pin? CZC solid pin?
Logged

Offline oldfrank

  • Sr. Member
  • ****
  • Posts: 870
Re: Help with CGW Disconnect
« Reply #4 on: October 20, 2013, 05:19:03 PM »
Stock I assume. It is hollow and flared on at least one end.

Sent from my Droid Razr

Logged

Offline 1SOW

  • Hero Member
  • *****
  • Posts: 15006
  • GO GREEN - Recycle 9MM
Re: Help with CGW Disconnect
« Reply #5 on: October 20, 2013, 05:46:39 PM »
That's stock and can be a minor PITA to remove and reinstall.
You would be very happy with either the CGW or the CZC solid firing pins that are very easy to remove/install and won't back out.  They are well worth the minor cost.
Logged

Offline oldfrank

  • Sr. Member
  • ****
  • Posts: 870
Re: Help with CGW Disconnect
« Reply #6 on: October 20, 2013, 06:11:53 PM »
Thanks, I am still new to the CZ platform and there is much to learn.
I will look into something new pin.
Thanks

Sent from my Droid Razr

Logged

Offline laserdoc

  • Sr. Member
  • ****
  • Posts: 724
Re: Help with CGW Disconnect
« Reply #7 on: October 20, 2013, 08:39:16 PM »
Hey frank,
Did you shoot this month at Cherokee Idpa?
Logged
CZ-75 polished stainless
CZ-75 compact 9mm
CZ-82 x 2, 9x18 Makarov
CZ-550 FS  308 cal
CZ 452 Trainer 22 LR
Ruger .22SR
Ruger Mark lll
REM 700  MTN rifle 7mm 08
H&R .20 gauge slug gun/thumb-hole stock

Offline oldfrank

  • Sr. Member
  • ****
  • Posts: 870
Re: Help with CGW Disconnect
« Reply #8 on: October 20, 2013, 08:53:27 PM »
No,Grand Son turned 4.

Sent from my Droid Razr

Logged
Pages: [1]   Go Up
« previous next »