« previous next »
Pages: 1 ... 3 4 [5] 6   Go Down

Author Topic: SLOW RUST BLUING REFINISH  (Read 20115 times)

0 Members and 1 Guest are viewing this topic.

Offline Rhino

  • Hero Member
  • *****
  • Posts: 663
Re: SLOW RUST BLUING REFINISH
« Reply #60 on: January 02, 2016, 07:43:21 AM »
You are a tinkerer, satisfaction will always elude you as it does the rest of us.
Logged

SPO1SHADOW

  • Guest
Re: SLOW RUST BLUING REFINISH
« Reply #61 on: January 02, 2016, 09:25:06 AM »
You may be on to something .........
« Last Edit: January 02, 2016, 09:27:06 AM by SPO1SHADOW »
Logged

SPO1SHADOW

  • Guest
Re: SLOW RUST BLUING REFINISH
« Reply #62 on: January 02, 2016, 10:39:31 PM »
Installed the new CGW hammer today, adjusted the trigger bar spring for 5/32" above the bar and fitted the safety to the new hammer. I think a little skate board tape to the front and rear of the grip frame and we will call this project done. I came out with a crisp 2 pound single action pull and a 6.5 pound double action as smooth as glass. Thanks for riding along with me.

Logged

Offline gprean

  • Newbie
  • *
  • Posts: 1
Re: SLOW RUST BLUING REFINISH
« Reply #63 on: January 02, 2016, 11:15:01 PM »
Amazing!!!
Logged

Offline straightwall01

  • Jr. Member
  • **
  • Posts: 49
Re: SLOW RUST BLUING REFINISH
« Reply #64 on: January 02, 2016, 11:16:37 PM »
Logged

Offline Psyop96

  • Hero Member
  • *****
  • Posts: 2691
Re: SLOW RUST BLUING REFINISH
« Reply #65 on: January 03, 2016, 01:56:48 AM »
Thanks you for sharing the ride with us. It's one of those posts that had me checking to see what's next in eager anticipation. I'm looking forward to  having some bluing work done in the future and, not knowing anything about the process, it was quite informative to see the work involved and the transformation. I'll now always look at those surplus CZs and imagine the possibilities!
Logged

Offline Winkel

  • Sr. Member
  • ****
  • Posts: 901
Re: SLOW RUST BLUING REFINISH
« Reply #66 on: January 03, 2016, 05:05:51 PM »
Wow, that really looks fantastic!  Nice job!
Logged

SPO1SHADOW

  • Guest
Re: SLOW RUST BLUING REFINISH
« Reply #67 on: January 03, 2016, 06:06:33 PM »
I discovered a few things today during an extended test session. Every now and then the hammer would fall to the half cock notch during single action fire. I took it back apart and stoned an angle on the lower half of the wing on the #1 disco. This solved that problem. I polished up the whole disco and re-installed it. Fired another 400 rounds of perfection. Also, the VZ grips pictured were keeping the Meg-Gar aftermarket magazines from entering easily or dropping free. The grip panels enter the magazine well just enough to make magazine extraction difficult by rubbing on each side. I had previously opened the magazine well in the upper and lower part of the frame so it would accept both pre-B and aftermarket mags so this had me going for a brief while. I installed a set of factory rubber grips and the problem was gone. I have a set of checkered Rosewood grips being made for the gun but the factory rubbers will do just fine until they arrive. Thanks again for all the kind words and comments.
« Last Edit: January 06, 2016, 07:04:35 PM by SPO1SHADOW »
Logged

SPO1SHADOW

  • Guest
Re: SLOW RUST BLUING REFINISH
« Reply #68 on: January 03, 2016, 06:13:23 PM »
Quote from: Psyop96 on January 03, 2016, 01:56:48 AM
Thanks you for sharing the ride with us. It's one of those posts that had me checking to see what's next in eager anticipation. I'm looking forward to  having some bluing work done in the future and, not knowing anything about the process, it was quite informative to see the work involved and the transformation. I'll now always look at those surplus CZs and imagine the possibilities!

That is what I see every time I look at one of those old beaten up guns. I did a restoration on a BD earlier this year that was in much worse condition than this one and it turned our very nice.
Logged

SPO1SHADOW

  • Guest
Re: SLOW RUST BLUING REFINISH
« Reply #69 on: January 06, 2016, 05:57:30 PM »
I received my grips in today and installed them. I am done with this project and have started on another. A friend purchased a really screwed up BD off of Gunbroker and I agreed to do a resto on it. If you are interested in seeing it let me know. This one is going to take a while.

Logged

Offline arkadi

  • Jr. Member
  • **
  • Posts: 43
Re: SLOW RUST BLUING REFINISH
« Reply #70 on: January 06, 2016, 06:04:45 PM »
Yes, please post the progress with new gun too.
Logged

Offline Goldcomet

  • Jr. Member
  • **
  • Posts: 76
Re: SLOW RUST BLUING REFINISH
« Reply #71 on: January 06, 2016, 06:16:23 PM »
Quote from: arkadi on January 06, 2016, 06:04:45 PM
Yes, please post the progress with new gun too.
+1 on that. I was very impressed with your results on the gun and it was a very interesting read.
Logged

Offline Psyop96

  • Hero Member
  • *****
  • Posts: 2691
Re: SLOW RUST BLUING REFINISH
« Reply #72 on: January 06, 2016, 07:15:02 PM »
You can't stop at just one with CZs. Feed the addiction with another rebuild progress.
Logged

Offline straightwall01

  • Jr. Member
  • **
  • Posts: 49
Re: SLOW RUST BLUING REFINISH
« Reply #73 on: January 06, 2016, 07:36:38 PM »

Quote from: arkadi on January 06, 2016, 06:04:45 PM
Yes, please post the progress with new gun too.

Please post new project!


Sent from my iPhone using Tapatalk
Logged

Offline Earl Keese

  • Hero Member
  • *****
  • Posts: 5191
Re: SLOW RUST BLUING REFINISH
« Reply #74 on: January 06, 2016, 08:14:39 PM »
I'd like to see a thread on the new project as well.
Logged
Pages: 1 ... 3 4 [5] 6   Go Up
« previous next »