Loose Sear Cage Fix - CZ 75 Variant Safety Models

[Tok36]

Nice! I believe there are even more gems waiting for us, hidden with the forums. The accumulated knowledge if this place is deep and it is always building. Keep looking and we will find them.

[1SOW]

Has anyone got a pic of the TAC Sport setup with springs used to hold the sear steady?  Where does it contact the sear?
Using a variation of Toks method,  it might be possible to weld a flat thin piece of metal to the top of the existing pin and use a spring or a flat piece of spring steel to do the same job.  ?? Maybe?


The flat vs angled surface of the mod, might be easier to fit and self-align when installed.  Maybe?

Too much time on my hands.  My Marine buddy out shot me with his STI  40 Cal Limited pistol  today at practice.

[Tok36]

I plan on posting some full disassembly coverage on the TS when i detail strip mine including close ups of the TS sear cage desing. For now you can get a decent look at TS sear cage spring set up in this video .

CZ 75 Tactical Sport Reassembly and Modifications (time: 18:55)
https://www.youtube.com/watch?v=4_vzv8jNxdk

[greystonedog]

I have a 75 and a 97 both with SAO and CGW hammer, couldn't figure why the 97 trigger was crisp and the 75 trigger not so crisp. Not noticeable every pull , maybe 1 in 3.Polished the heck out of the 75 internals with no improvement. Did the sear cage fit with the extended pin  on the 75 and it worked wonders.. Not difficult , took about 2 hrs , need to take down the pin top a bit at a time to get a snug fit. Thanks TOK for this great information!

[SlvrDragon50]

I will be doing it this week courtesy of Scarlett Pistol. Can't wait!

[Scarlett Pistol]

I will be doing it this week courtesy of Scarlett Pistol. Can't wait!

BTW I cut yours to do it the way Tok has I  his pictures. Let me know if you need any more (incase 3 isn't enough or I somehow cut them too short...)

Sent from my Nexus 5X using Tapatalk

[SlvrDragon50]

Just did the mod to my S2! Tremendous improvement! Absolutely zero creep now. Trigger pull in SA is also now 2lb 10 oz. so it dropped a tad.

[Scarlett Pistol]

Just did the mod to my S2! Tremendous improvement! Absolutely zero creep now. Trigger pull in SA is also now 2lb 10 oz. so it dropped a tad.

Woo-hoo! We've converted another! Gonna do it to the 85 now?

Sent from my Nexus 5X using Tapatalk

[SlvrDragon50]

Possibly another week. To be honest, I haven't pulled my 85C out since I got my S2. I only bring it to the range when I bring friends to shoot

If it were easier for me to sell it, I would sell it and pick up another gun!

But seriously though.. takes like no time at all to do this mod if you have a dremel. And MASSIVE improvement.

[zeroryde]

Man I gotta try this on my S2 now.

Sent from my Pixel XL using Tapatalk

[copemech]

I may need a couple of these, what are they?
 

[1SOW]

Me 2.

[Scarlett Pistol]

I may need a couple of these, what are they?
 

Me 2.

You mean the pieces of steel rod for doing the mod? I can cut a few more from the piece I ordered. Shoot me a PM w your info and I'll snail mail to you two. If you want if Amazon 2 day priority shipping I charge $20... [emoji48]

That's goes for anyone else. At least until I run out. I can probably cut 6 or 8 pieces out of my rod.

Sent from my Nexus 5X using Tapatalk

[Scarlett Pistol]

Cut my rod down and have about 10 pieces left as spares. For the mod 0.6" has been plenty but since the metal heats where I cut it I have cut at about 0.7" to 0.8" just to give some extra length. Cooled after each cut, so it shouldn't have tempered it and I don't think it gets hot enough to temper from these cuts. Since I don't know for sure I played it safe. First come first serve with freebies.

[sniperboy]

Like many of the regulars here, you are a saint, a scholar and a hero Scarlett Pistol!  Thank you.  I hope we can return the good karma some day.