Loose Sear Cage Fix - CZ 75 Variant Safety Models

[greystonedog]

dremel tool is best,take off a little at a time so the sear cage fits tight

[anonymouscuban]

OK fellas. May need some help here.

So I made the new pin. Got it fitted. Sears back in. Clears the slide. Action is working in both DA and SA. However...

The SA reset isn't as audible. Before there was a nice click. Now, the reset is quite faint. Also, it's not as tactile.

I'm running the CGW race hammer and adjustable sear.

Again, everything works but that reset just doesn't seem right or to my liking.

Any ideas?

Sent from my SM-G930U using Tapatalk

[Tok36]

   The modification can move the sear cage forward in the frame. This can change the feel of the reset. You can try increasing the trigger bar spring tension.

What disco do you have installed?

[timmy75]

i have problem with DA, it became grittier after mod. competition hammer.
it feels like sear is fixed and rubbing hammer at the end of DA pull. before sear was like free floating and smoother (in DA).

but SA is fantastic. i could not ever imagine DA/SA trigger can be close to 1911.

[anonymouscuban]

   The modification can move the sear cage forward in the frame. This can change the feel of the reset. You can try increasing the trigger bar spring tension.

What disco do you have installed?

Did the trick. Increased the tension on the trigger bar spring and the reset feels normal again. Thanks!

Sent from my SM-G930U using Tapatalk

[Scarlett Pistol]

i have problem with DA, it became grittier after mod. competition hammer.
it feels like sear is fixed and rubbing hammer at the end of DA pull. before sear was like free floating and smoother (in DA).

but SA is fantastic. i could not ever imagine DA/SA trigger can be close to 1911.

When you say

it became grittier after mod. competition hammer.

I am assuming you mean you did this mod and added the competition hammer. Correct? If so, do you still need help?

[Madbutcher]

Hi,

Very usefull information!

Did the pin today, I found out that you can use the extractor pin for the job it is the precise height and diameter so I only had to vile it down to the correct fitting size!

Very thankful that you shared the detailed instructions to do the job.
Hammer breaks so sweet right now and there is no movement in the sear cage.

That's all folks, greetings from the Netherlands!

[Tok36]

Hi,

Very usefull information!

Did the pin today, I found out that you can use the extractor pin for the job it is the precise height and diameter so I only had to vile it down to the correct fitting size!

Very thankful that you shared the detailed instructions to do the job.
Hammer breaks so sweet right now and there is no movement in the sear cage.

That's all folks, greetings from the Netherlands!

Glad that it worked out. Thank you for the tip.

[CZFanGrrl]

I was directed here by one of my subscribers.  This is a gold mine of info!  Thank you for sharing your knowledge!

[pcar157]

CZFanGrrl. welcome! Have seen many of your youtube videos and love them. Best to you and enjoy the forum!

[CZFanGrrl]

CZFanGrrl. welcome! Have seen many of your youtube videos and love them. Best to you and enjoy the forum!

Thank you! 

[sniperboy]

So after 6 years from doing this project I got a P-01 that needed this extended #19 pin mod.

Just my good deed for the day, turns out that a 2" wide BINDER CLIP (the arms) are just the perfect diameter for this pin.  Saved me a lot of time from having to turn down thicker stock.
Brand is UNIVERSAL and it is marked No. 100 LARGE on it.

If you have some in the office lying around its much more convenient than buying rods from Amazon (now out of stock) or using an expensive CZ extractor pin.  The CZ extractor pin is the perfect diameter and length, but its still $3 a pop.  Costly if you mess up.