P10C RMR cowitness stock sights

[Ferris13]

Any issues with mounting an RMR this low on the slide?  I came across this on instagram and I'm interested but haven't seen a mount this low yet on the P10C and curious if there could be any possible issues?
https://www.instagram.com/p/BaQDcGyHGM5/

[ranastas]

Mechanics aside, the rmr gets a heavy coat of carbon in that position.
I don?t know their work and don?t want to bash, but their are too many good shops doing it the right way (opinion) some even members of this forum.


Sent from my iPhone using Tapatalk

[earlan357]

I still don't think it will co-witness well with stock sights.  JagerWerks milled my RMR pocket .185" below the slide surface (same depth as the factory rear sight dovetail) and I could barely see my .225" Dawson P09 front/.245" Dawson Glock MOS rear sights.  The factory #3 front is ~.150" tall.  So unless the pocket is milled over 1/4" deep, there would still only be a sliver of iron sights to use.

I also wonder how much thread engagement the right side mounting screw has, since it sits right over the extractor.  Mine is well clear and doesn't block the extractor pin which is a plus.



For reference, here's my co-witness with .225" tall front sights and a .185" deep rmr cut.  It's really only usable for slow target shooting, so I've since replaced with in a .265" Dawson P09 front/.280" Ameriglo Glock rear.

[Ferris13]

Thanks for the pics Earlan very helpful.  Yeah i think you're right as far as how hard it might be to use the stock sights even if they do mill that low.  They had another picture of the cowitness and it barely had clearance.  How are you liking the rear sight placement in front of the RMR? 

[earlan357]

Thanks for the pics Earlan very helpful.  Yeah i think you're right as far as how hard it might be to use the stock sights even if they do mill that low.  They had another picture of the cowitness and it barely had clearance.  How are you liking the rear sight placement in front of the RMR?

I had an MOS Glock with the iron sight to the rear, but once I tried irons forward in a class I switched.  The sight radius is a little shorter than say a Glock 26, but they don't block the dot or distract from it.  As an added bonus the sight protects the RMR a bit from brass and the rear sights corners no longer poke little mouse holes in my shirts.

[ISYMFS334]

earlan357 can you tell me the exact sights you have in the pic you have post on the czP10c? I wanting some that sit as low as possible.

[earlan357]

earlan357 can you tell me the exact sights you have in the pic you have post on the czP10c? I wanting some that sit as low as possible.

Dawson P09 .215" Fiber Front
Dawson Glock MOS .225" Rear

That pic is misleading.  When viewed at arms length, about 1/2" the fiber dot is covered by the RMR body.  I'm much happier with a .265" front and an Ameriflo GL-408 Rear shown below:

[Christopher67]

Anyone had work done by these guys, I've heard good things about them.


  https://www.instagram.com/jagerwerks/     

[earlan357]

Anyone had work done by these guys, I've heard good things about them.


  https://www.instagram.com/jagerwerks/     

I've had a few done.  Black Nitride adds a few weeks, but it's much more resilient to holster wear.

Here's a write-up of the work they did on my P10c:
https://minivandoorgunner.blogspot.com/2017/10/cz-p-10c-jagerwerks-rmr-cut.html


P320


G26


G19


G34

[Christopher67]

Anyone had work done by these guys, I've heard good things about them.


  https://www.instagram.com/jagerwerks/     

I've had a few done.  Black Nitride adds a few weeks, but it's much more resilient to holster wear.

Here's a write-up of the work they did on my P10c:
https://minivandoorgunner.blogspot.com/2017/10/cz-p-10c-jagerwerks-rmr-cut.html


P320


G26


G19


G34

Thanks Earl, much appreciated!

[Evo_newb]

Hey Earlan357,

With that slide set up, what holster do you use?  I got my p10c a while back, but not real sure on a holster option with an optic and co-witness sights or if that is even possible to find.

Thanks,

[2morechains]

After I RMR?s my P10C I modified a JM Custom AIWB holster to clear thr RMR and BUIS.  It was pretty easy to do with a dremel cutting wheel and sanding drum.  Also had to change the shape of the sweatguard slightly using a heat gun. 

Later when I settled on a WML I contacted Shooks Custom to order one of his AIWB holsters molded specifically for a RMR?d P10C with taller irons and O-Light PL Mini.  Been wearing that daily as of late including some 6 hr long drives and have been impressed how comfortable it is. 

[Evo_newb]

Thanks for the ideas 2more!

[earlan357]

Hey Earlan357,

With that slide set up, what holster do you use?  I got my p10c a while back, but not real sure on a holster option with an optic and co-witness sights or if that is even possible to find.

Thanks,

Armordillo Concealment Lux.

[Evo_newb]

Thanks Earlan357!