Rami sight dissapointment..

[charlestheforth]

did they just send me the wrong sight then?  When you knocked out the original front sight what number was written on the bottom?  Mine is #2  and the new dawson fiber optic sight is significantly taller than the factory front sight.   

[mecenas]

If you ordered directly from Dawson, I doubt they would send the wrong one. Other vendors might.
One of forum members showed his Dawson front fiber optic that stuck out at front of the muzzle. Obviously not the way it should fit, but it was not purchased from Dawson

[Vinny]

And to get back to OP.......
Those new RAMI Trijicon sights from CGW look really nice.

IMHO very close to my spare parts 'creation'. 

Tvey do look very nice. However, I?m leaning towards throwing a RMR on mine with CGW milled slide. I want to set it up so that it co witnesses with suppressor height sights if possible.

+1  I'm planning to send CGW my 'other' RAMI slide tomorrow from back-up gun. CGW seems to have best understanding of what's required to make this work properly.
They offered three good RDS options: one for DPPro, another for Venom, and a third with RMR (with the Dueck plate BUIS). I have an extra RMR so the choice was easier for me. If I don't like the position of Dueck front iron I could have it milled off and use a matched sight at muzzle. However, videos I've seen are favorable with the BUIS plate and a touch of green fluorescent paint on front post should do it for me.  YMMV

Just got my RAMI BD back from CGW with the Dueck plate milled in beautifully with the RMR. Nice work! Can't get to the range until Wednesday, but the BUIS angle looks right and IMHO the RMR is about perfect for the RAMI!

[MeatAxe]

And to get back to OP.......
Those new RAMI Trijicon sights from CGW look really nice.

IMHO very close to my spare parts 'creation'. 

Tvey do look very nice. However, I?m leaning towards throwing a RMR on mine with CGW milled slide. I want to set it up so that it co witnesses with suppressor height sights if possible.

+1  I'm planning to send CGW my 'other' RAMI slide tomorrow from back-up gun. CGW seems to have best understanding of what's required to make this work properly.
They offered three good RDS options: one for DPPro, another for Venom, and a third with RMR (with the Dueck plate BUIS). I have an extra RMR so the choice was easier for me. If I don't like the position of Dueck front iron I could have it milled off and use a matched sight at muzzle. However, videos I've seen are favorable with the BUIS plate and a touch of green fluorescent paint on front post should do it for me.  YMMV

Just got my RAMI BD back from CGW with the Dueck plate milled in beautifully with the RMR. Nice work! Can't get to the range until Wednesday, but the BUIS angle looks right and IMHO the RMR is about perfect for the RAMI!

What do you use to holster that, with the RMR sight in place?

[Vinny]

And to get back to OP.......
Those new RAMI Trijicon sights from CGW look really nice.

IMHO very close to my spare parts 'creation'. 

Tvey do look very nice. However, I?m leaning towards throwing a RMR on mine with CGW milled slide. I want to set it up so that it co witnesses with suppressor height sights if possible.

+1  I'm planning to send CGW my 'other' RAMI slide tomorrow from back-up gun. CGW seems to have best understanding of what's required to make this work properly.
They offered three good RDS options: one for DPPro, another for Venom, and a third with RMR (with the Dueck plate BUIS). I have an extra RMR so the choice was easier for me. If I don't like the position of Dueck front iron I could have it milled off and use a matched sight at muzzle. However, videos I've seen are favorable with the BUIS plate and a touch of green fluorescent paint on front post should do it for me.  YMMV

Just got my RAMI BD back from CGW with the Dueck plate milled in beautifully with the RMR. Nice work! Can't get to the range until Wednesday, but the BUIS angle looks right and IMHO the RMR is about perfect for the RAMI!

What do you use to holster that, with the RMR sight in place?

Excellent question. I tried it today in my existing Vedder OWB kydex with forward cant and I'm going to have to do a little trimming. I think it will work fine, but before I do that I'm going to check with Vedder to see if they can make another with the clearance I need. I'll keep the one I have for my other RAMI.