Baby Uplula

[viking499]

Will this work on the 75 Kadet mags or does it need to be a fullsize modified Uplula.

[Tok36]

Full size modified, the Baby lula is too narrow for the CZ Kadet magazines. CZ Kadet mags are similar in dimension to the factory CZ 9mm/40 S&W mags so that you can use them in a 75 variant frame/lower once you install a Kadet slide.

[viking499]

Thanks Tok

[DenStinett]

Full size modified, the Baby lula is too narrow for the CZ Kadet magazines. CZ Kadet mags are similar in dimension to the factory CZ 9mm/40 S&W mags so that you can use them in a 75 variant frame/lower once you install a Kadet slide.

Todd:
As Tok said, the Baby is for SOME Single Stack Mags only, not even a 1911 Mag will fit in it either
MagLULA does make the 22UpLULA
It is designed for Double Stack 22 (or .17) Mags ONLY
It's Top Yoke has a limiter so it only open enough to allow Rimfire Rounds to fit under it
And the Beak is shorter by about an eighth of an inch

[Trblshtr]

I use the 22UpLula to load my Kadet mags, almost a requirement when the magazines are new (where I found it impossible to get the last couple rounds in).  After running a few hundred rounds through each mag I can finally load them by hand but still often use the 22UpLula as it's somewhat quicker.

[DenStinett]

The 22UpLULA is nice .... for loading .22 (or .17) Mags ONLY

I thought it was funny;
That when the UpLULA first came-out, MagLULA made fun of HKS;
Saying that you needed several of their (HKS) Loaders, to load all the different Magazines out there
And that the UpLULA was a "One Loader does it all" type of deal
But the UpLULA didn't load most .380s and really nothing smaller than a 9mm
Then MagLULA offered their BabyUpLULA, for Single Stack Mags only .... but it doesn't even fit the 1911 Mags ....
What's up with THAT ? ! ?
THEN their 22UpLULA comes out .... mainly for us KADET Owners and all the other .22 Conversion Mags out there
So now you need all 3 MagLULA UpLULA Loaders, and you STILL can't load any Double Stack Magazines smaller than a 9mm, but larger than a .22lr, i.e a CZ 82 / 83 ! ! !

MagLULA should scrap all three of their current designs and just make one;
A Double Stack, .22 thru .45 .... Let's call it .... the UpLula-K   

[AZ_CZ]

Don't forget the model-specific up-lula just for Uzi owners.

I think it's a great style loader for ARs but a modified HKS style for the Kadet is sweet. I love how it "holds" the mag so I dont have to jam it against something .

[larryflew]

DenStinett

MagLULA should scrap all three of their current designs and just make one;
A Double Stack, .22 thru .45 .... Let's call it .... the UpLula-K   



Or make one like your mod that works with all and call model UlLula- D

[eastman]

Don't tell my vz82 that the Uplula doesn't work, she thinks it works fine.

[DenStinett]

Don't tell my vz82 that the Uplula doesn't work, she thinks it works fine.

I would guess it all depends on which Caliber it's in

[eastman]

Don't tell my vz82 that the Uplula doesn't work, she thinks it works fine.

I would guess it all depends on which Caliber it's in

9x18mm Mak, but I've also used it for the 83 with 9x17.

[larryflew]

Don't tell my vz82 that the Uplula doesn't work, she thinks it works fine.

I would guess it all depends on which Caliber it's in

9x18mm Mak, but I've also used it for the 83 with 9x17.

Should work on any 9 mm and 380.  Too wide for 32 and 22.  Den's modified works for all from my 44 Desert eagle to my Kadet.

[sberres]

I just use the Den-mod version to load everything- single stack, double stack, 22, 380, 9, 40. Everyone complaining about the Taurus 22 mini-button difficult just needs to use this instead.  It’s about as close to universal as can be.

[K3JB]

I have found Den's mod reloader to work great. Actually used it today with a couple of new .22 shooters.
I purchased mine years ago from Den and it has worked flawlessly.