« previous next »
Pages: 1 2 3 [4]   Go Down

Author Topic: P-10c Ejector  (Read 15804 times)

0 Members and 1 Guest are viewing this topic.

Offline vath

  • Newbie
  • *
  • Posts: 20
Re: P-10c Ejector
« Reply #45 on: December 19, 2020, 05:29:00 PM »
Quote from: vath on October 21, 2020, 08:08:38 PM
I spoke to CZ-USA and they are sending me out replacements for #5 and #17. Great customer service!
 ;D
After a mix up at the CZ USA parts department, they finally (and quickly) sent me out my replacement parts.  Definitely a downward slope on this replacement rear insert.  I must say a great customer service experience with CZ USA.  I'm not sure if I'm going to throw this in just yet...


Sent from my SAMSUNG-SM-G930A using Tapatalk

Logged

Offline Togmaster

  • Full Member
  • ***
  • Posts: 424
Re: P-10c Ejector
« Reply #46 on: December 19, 2020, 08:27:27 PM »
Yea that's got to go back to CZ.
Logged
Let's go Brandon!

Offline vath

  • Newbie
  • *
  • Posts: 20
Re: P-10c Ejector
« Reply #47 on: December 19, 2020, 08:41:58 PM »
Do we even know what normal is supposed to be shaped like?

Sent from my SAMSUNG-SM-G930A using Tapatalk

Logged

Offline Duke Nukem

  • Full Member
  • ***
  • Posts: 249
Re: P-10c Ejector
« Reply #48 on: December 19, 2020, 09:30:39 PM »
Quote from: vath on December 19, 2020, 08:41:58 PM
Do we even know what normal is supposed to be shaped like?

Sent from my SAMSUNG-SM-G930A using Tapatalk

Good question.  I don't think these have to be perfectly straight to function properly, and they don't seem to be arrow straight as new parts, but I haven't seen one angled down like that one is (although relatively few pics have been posted here).
Logged

Offline tjwolf

  • Jr. Member
  • **
  • Posts: 53
Re: P-10c Ejector
« Reply #49 on: December 22, 2020, 09:36:10 PM »
My P10S made 2019 in Czech Republic  is completely straight.

Sent from my SM-N950U Note 8 using Tapatalk

Logged
Dual tone CZ 75B (2010), CZ 75B Black, CZ P-09, CZ -P07 9mm, CZ 75 Compact.

Offline tjwolf

  • Jr. Member
  • **
  • Posts: 53
Re: P-10c Ejector
« Reply #50 on: December 22, 2020, 09:36:59 PM »
Quote from: tjwolf on December 22, 2020, 09:36:10 PM
My P10S made 2019 in Czech Republic  is completely straight.

Sent from my SM-N950U Note 8 using Tapatalk
Sorry for large pics.

Sent from my SM-N950U Note 8 using Tapatalk

Logged
Dual tone CZ 75B (2010), CZ 75B Black, CZ P-09, CZ -P07 9mm, CZ 75 Compact.

Offline dehughes

  • Jr. Member
  • **
  • Posts: 83
Re: P-10c Ejector
« Reply #51 on: December 24, 2020, 12:21:15 AM »
Yeah, the ejector in my P10F looks just like the one from tjwolf. As well, when I insert an empty magazine it does push the slide stop lever into the bottom of ejector, but with nowhere near enough force to cause any damage or bending, even if I slam the mag home.  I’d say something happened at the factory to cause your ejector to be bent downward like that and it is definitely not right.
Logged

Offline anach

  • Jr. Member
  • **
  • Posts: 53
Re: P-10c Ejector
« Reply #52 on: December 26, 2020, 02:14:45 AM »
Quote from: vath on December 19, 2020, 05:29:00 PM
Quote from: vath on October 21, 2020, 08:08:38 PM
I spoke to CZ-USA and they are sending me out replacements for #5 and #17. Great customer service!
 ;D
After a mix up at the CZ USA parts department, they finally (and quickly) sent me out my replacement parts.  Definitely a downward slope on this replacement rear insert.  I must say a great customer service experience with CZ USA.  I'm not sure if I'm going to throw this in just yet...

Holy Batman... I suspected CZ was having QC issues with some of the parts, but that's insane. Worst of all, someone actually put that in an envelope and shipped it out of the warehouse.

If instead that's a new Rev3 part, then some CZ engineer had a big brained idea that to keep the ejector from bending up, they would just bend it down the other way. A lot. Almost looks like a machineshop joke...

I suspect that is going to cause issues with feeding since the top round in a mag is probably going to nose-up when it hits the ejector.
Logged

Offline vath

  • Newbie
  • *
  • Posts: 20
Re: P-10c Ejector
« Reply #53 on: December 26, 2020, 08:35:43 AM »
I'll be calling CZ back to inquire about this downward sloped replacement insert.

Sent from my SAMSUNG-SM-G930A using Tapatalk

Logged

Offline jackal2001

  • Newbie
  • *
  • Posts: 20
Re: P-10c Ejector
« Reply #54 on: December 26, 2020, 10:10:33 AM »
My p10c OR has a slight upward bend to it. It doesn't look like the rounds are making contact with the ejector.  Model 95130 1/10/2020 mfg date.

Sent from my SM-G973U using Tapatalk

Logged

Offline PFran42

  • Jr. Member
  • **
  • Posts: 27
Re: P-10c Ejector
« Reply #55 on: December 28, 2020, 06:33:13 PM »
Just checked one of my brand new unfired FDE frames. It looks flat at first glance but if you place a straight edge over the ejector, you see a little light in the location where most are seeing the slight upturn of the bend.
Logged

Offline vath

  • Newbie
  • *
  • Posts: 20
Re: P-10c Ejector
« Reply #56 on: January 11, 2021, 12:34:22 PM »


Quote from: vath on December 19, 2020, 05:29:00 PM
Quote from: vath on October 21, 2020, 08:08:38 PM
I spoke to CZ-USA and they are sending me out replacements for #5 and #17. Great customer service!
 ;D


Sent from my SAMSUNG-SM-G930A using Tapatalk

Just called CZ again regarding this downward bent insert.  They've confirmed it should be straight , a little bend up or down wouldn't affect function of the firearm, but they believe my replacement was bent during shipment.  They also checked a bin of inserts and said they are straight and this shouldn't be a QC issue.

They are sending me another replacement insert. :)

They also mentioned that some people using extended magazines and slamming the magazine home doesn't help the situation for the ones that bend or break upward.

Sent from my SAMSUNG-SM-G930A using Tapatalk

Logged

Offline anach

  • Jr. Member
  • **
  • Posts: 53
Re: P-10c Ejector
« Reply #57 on: January 13, 2021, 05:51:05 AM »
Quote from: vath on January 11, 2021, 12:34:22 PM

Just called CZ again regarding this downward bent insert.  They've confirmed it should be straight , a little bend up or down wouldn't affect function of the firearm, but they believe my replacement was bent during shipment.  They also checked a bin of inserts and said they are straight and this shouldn't be a QC issue.


If you believe that line, I've got a bridge in a lovely little city called Manhattan...  ::)

Unless they shipped it in a paper envelope with zero padding and someone closed it in a door jamb, it's a part designed to be smashed into a brass case at high velocities, over and over and over. They shipped it like that  ;D
Logged

Offline vath

  • Newbie
  • *
  • Posts: 20
Re: P-10c Ejector
« Reply #58 on: January 16, 2021, 02:20:02 PM »
Latest ejector replacement almost exactly matches the one that came stock in my P-10C.  I guess I will leave it be and have backups of it breaks...
(both images are the new ejector)

Sent from my SAMSUNG-SM-G930A using Tapatalk

Logged

Offline anach

  • Jr. Member
  • **
  • Posts: 53
Re: P-10c Ejector
« Reply #59 on: January 23, 2021, 06:38:51 PM »
Any chance we gan get a sticky for the P10 family ejector? This seems to come up over and over, and having vath's picture of an uninstalled and unfired (and not completely borked like the first one) ejector block would be nice to point people to.
Logged
Pages: 1 2 3 [4]   Go Up
« previous next »