« previous next »
Pages: [1]   Go Down

Author Topic: Red dot on PCR  (Read 3309 times)

0 Members and 1 Guest are viewing this topic.

Offline wbnash

  • Jr. Member
  • **
  • Posts: 54
    • Law Office of Walter Nash
Red dot on PCR
« on: September 30, 2023, 10:53:38 AM »
My aging eyes are needing red dot sights more than ever these days. 

I am thinking of having the slide on my PCR milled (or to get a spare slide and mill it) for a red dot.

Is the slide wide enough to mill for an RMR/Holosun "full size" red dot (508 for example) or must one go with the smaller sight (Holosun 507K or RMRcc)?

Thanks!
« Last Edit: September 30, 2023, 05:30:55 PM by wbnash »
Logged
P-10 C OR
75 D PCR Compact
SP-01 Shadow
452 American

Offline Crawl

  • Full Member
  • ***
  • Posts: 362
Re: Red dot on PCR
« Reply #1 on: September 30, 2023, 12:00:27 PM »
My experience with the Holosun K optics has been that they have unacceptable parallax problems. They're the only Holosun optic with this issue. However, the EPS Carry doesn't suffer from the problem, and it fits the width of the slide just right. You can also use a Shield RMS on the same footprint.
Logged

Offline AZ_CZ

  • Hero Member
  • *****
  • Posts: 3298
Re: Red dot on PCR
« Reply #2 on: September 30, 2023, 12:18:58 PM »
Quote from: Crawl on September 30, 2023, 12:00:27 PM
My experience with the Holosun K optics has been that they have unacceptable parallax problems. They're the only Holosun optic with this issue.

What kind of issues? Did a quick Google but didn’t see anything definitive. I have them on a P10C and a Canik Mete SFx Pro. Don’t have a lot of trigger time with either one yet, less than 500/each, but haven’t noticed anything at the 15 and 25 yard lines.

OP love my PCR and will follow to see if someone has figured this out. I’ve seen pictures of it done but by eliminating the LCI or removing the rear sight but don’t recall if they were using a C or K model.
Logged
CZ Fanbot since 1996

Offline Crawl

  • Full Member
  • ***
  • Posts: 362
Re: Red dot on PCR
« Reply #3 on: September 30, 2023, 12:20:41 PM »
The ones I have used have all had a parallax shift which made the optics impossible to zero. If you have one that doesn't have the issue, that's great news, and I'd use that footprint (specifically that optic) on a CZ75 slide before anything else.
Logged

Offline Born2vette

  • Full Member
  • ***
  • Posts: 275
Re: Red dot on PCR
« Reply #4 on: September 30, 2023, 03:42:49 PM »
I have a 407k on my P365 and a 507k on my Rami. No issues zeroing, I practice regularly out to 25 yds without any issues or shift in zero. Both optics have had zero issues and both pistols are in my EDC rotation.

YMMV
Logged
SP-01 Tactical
75 D PCR fully Cajunized
2075 Rami B (9 mm), 85 trigger/reach reduction kit
75 SC Massada
97 B CGW reach reduction kit/‘flat’ trigger/race hammer
457 Varmint MTR
82, 9x18
P10C OR SR
Dan Wesson Valor V-bob black Duty finish
P10F OR
75 B

Offline Born2vette

  • Full Member
  • ***
  • Posts: 275
Re: Red dot on PCR
« Reply #5 on: September 30, 2023, 03:47:22 PM »
My Rami





Sent from my iPad using Tapatalk
Logged
SP-01 Tactical
75 D PCR fully Cajunized
2075 Rami B (9 mm), 85 trigger/reach reduction kit
75 SC Massada
97 B CGW reach reduction kit/‘flat’ trigger/race hammer
457 Varmint MTR
82, 9x18
P10C OR SR
Dan Wesson Valor V-bob black Duty finish
P10F OR
75 B

Offline wbnash

  • Jr. Member
  • **
  • Posts: 54
    • Law Office of Walter Nash
Re: Red dot on PCR
« Reply #6 on: September 30, 2023, 04:31:01 PM »
I have a 507 on a 365 and on my wife's Sig P322.  So far no issues.

My main concern is dot width on the narrower CZ PCR slide.  Some folks have told me that there is a lot of plate overhang with the full size dots (RMR and 508, for example).

Any advice on that?
Logged
P-10 C OR
75 D PCR Compact
SP-01 Shadow
452 American

Offline Born2vette

  • Full Member
  • ***
  • Posts: 275
Re: Red dot on PCR
« Reply #7 on: September 30, 2023, 07:10:41 PM »
I would stick with the k series.  507k is .98” wide, 507c is 1.24” wide.

PCR slide is



 
So if you go with a 507c (or 407c) you will get 1/4”+ overhang and will likely need to use a mounting plate which will raise the RDS higher. With the 507k you can directly mount the RDS to the slide with minimal overhang.

 My Rami slide is about the same width as a PCR


And I don’t feel anything larger than a 507k works well.

Just my 2 cents.  I have heard of people doing it but my preference would be for the lower, neater mount.  I have a Romeo1 on a dovetail mount on my SP-01 but am planning to get it milled at some point in the near future


Sent from my iPad using Tapatalk
Logged
SP-01 Tactical
75 D PCR fully Cajunized
2075 Rami B (9 mm), 85 trigger/reach reduction kit
75 SC Massada
97 B CGW reach reduction kit/‘flat’ trigger/race hammer
457 Varmint MTR
82, 9x18
P10C OR SR
Dan Wesson Valor V-bob black Duty finish
P10F OR
75 B

Offline kabong57

  • Full Member
  • ***
  • Posts: 147
Re: Red dot on PCR
« Reply #8 on: October 13, 2023, 10:19:31 PM »
« Last Edit: October 14, 2023, 08:08:43 AM by Wobbly »
Logged

Offline reddad

  • Newbie
  • *
  • Posts: 15
  • P-01 - P-01 - PCR - 2075 Rami
Re: Red dot on PCR
« Reply #9 on: October 17, 2023, 09:55:00 AM »
I have a 407k on a P-01 that fits perfectly with no overhang. I had Wager do the cut and he got it deep enough to co-witness with factory-height sights. Also, I didn't have any problems zeroing the 407k on the P-01 or on my Masada Slim.
Logged
Pages: [1]   Go Up
« previous next »