Drill Bit for Welded Trigger Pack - Pay it Forward

[oligoodday]

Add me to the list please. Picked up my scorpion over the weekend. Thanks!

[BucketShop]

Please put me on the list for the drill bit.

[BucketShop]

The bits have stopped circulating.  I can only track one and it hasn't moved in 12 days.

The posts are vague and it's hard to know who sent a pm to who.   I sent a couple pm's but I really am not sure who had which bit last.

[Warpspasm]

I responded to BucketShop, but I'm not sure if he got my PM. On the 18th snohomishcz sent me a PM asking for my address, so he could ship me the bit. I sent it to him. A few days later on the 20th I got another email asking for my address, so I responded again thinking snohomishcz didn't get my first response. I didn't realize until BucketShop contacted me today that the second PM was from Mk23 and not snohomishcz. So, theoretically I should have two of them, but I have none. I looked into my "Sent" message folder and it's completely empty. It doesn't even show the one that I sent to BucketShop. I'm not sure if anyone got any of the messages I sent to them. If they did not, then the bits should still be with snohomishcz and Mk23.  If they both (ore even one) show up here on some date I will pass them along after I use it. Hope this helps.

[BucketShop]

Thanks I got your pm but I'm not sure all the pm's I sent actually were.  I did not see MK23.   snohomishcz, Manny C and SV325 were the last people I could spot having bits.  A couple of those guys have <5 posts and haven't logged into the forum in weeks.
I asked on the Facebook Scorpion group as some people are members of both.

[snohomishcz]

I'm sending the bit to Warpspasm...... It might take a few days it's literally going coast to coast

[snohomishcz]

I'm in Washington state

[oligoodday]

Take me off the list. Was able to remove the collar w/ some bits I had. Thanks anyway!

[mannyc]

BucketShop, Read the posts again, it clearly show in there that I sent the bit to calimstng66, and he sent it to transger2, then transger2 sent it to Gritz.......... Don't know what you are trying to assume or portray us to be by saying with have less than 5 post and not log on for weeks, I don't like that.

[BucketShop]

My apologies Manny, your post was immediately under another one that said who gets it next? Your post said Ship bit to calimstng66.  That sounded more like instructions to the previous poster.  I would have understood Sent or Shipped  differently, but I see how you feel differently. 

It was not my initial intention to mention any names and I am sorry I did.  Apologies to anyone who took offense.  I also understand that being surrounded by the Louisiana flood complicates life terribly and my best wishes for that member who was affected. 

I NO LONGER need the drill bit but there are others that do.  I think it's tremendous that HBI donated these bits, as did one other member, and that they are circulating through the community.

Again, my apologies and God Bless.

[boomer1]

Please put me on the list for the drill bit. 

I have been dicking around with the POOR customer service at CZ-USA waiting for their trigger swap program to get off of the ground since early May.

Thanks.

[Pointcover]

Please put me down for the drill bit sharing.  Thank you for doing this!

[Warpspasm]

snohomishcz, did you actually have a chance to drop it into the mail stream? It still hasn't arrived as of today. If you mailed it on the 24th it should have been here by now..

[Warpspasm]

The bit came in the mail today. I worked on taking out the weld, but so far, no luck. The bit will barely cut the metal. I've been working at it for at least 40 minutes and the weld is still intact. It took forever to even get it to make a dimple, and now there's a cup in there, but I feel like it's rubbing the steel off as opposed to cutting it. I've been oiling to keep it cool, but I think this thing must have gotten dull or something. Do carbide bits get dull? I'm not sure what to do at this point.

[Warpspasm]

This thing is driving me nuts. I STILL haven't been able to drill through to the point of breaking the weld. Has anybody else had this problem? I probably have 20 minutes of actual drill to weld time at this point. I thinking the bit may be too dull, but having never used a carbide bit to drill a hardened weld I don't know.